JVC HR-S4800U manual Prepare tapes, Select editing function you want, Activate editing mode

EN 49

1	Make connections
	Connect an audio/video cable between the VCR’s
	audio/video input connectors and the other
	component’s audio/video output connectors.

2	Prepare tapes
	Load the source tape on the other VCR, and the
	tape to be edited on this VCR.
3
	Select input mode
	Select “F-1” — when connecting the other
	component to the audio/video input
	connectors on the front panel.
	Select “L-1” — when connecting the other
	component to the audio/video input
	connectors on the rear panel.
	On the front panel:
	Press CH5°.
	On the Remote:
	Press the Number key "0 (AUX)" or CH +/Ð.
4
	Select editing function you want
	Set “EDIT FUNCTION” to either “INSERT” or “AV

DUB” whichever you want to use by following the procedure described on pages 38 and 42.

c Make sure to set “EDIT FUNCTION” to “REC- PAUSE” after you finish editing tapes. This cancels the editing function.

8	Locate start point
	Use REW (	) or SHUTTLE ring to reverse the
	tape (See “Special Effect Playback”: Z pg. 28)
	When you find the begining of the scene you
	want to edit, press PAUSE

9	Activate editing mode
	Press REC ( ƒ) on the front panel

c Make sure to set the recording format (VHS, S- VHS or S-VHS ET) on the VCR is the same sa that of the original recording on the tape.

cDuring Insert Editing pause mode (, and

light up on the front display panel.)

cDuring A/V Dubbing pause mode ( and blink, and light up on the front display panel.)

0	Start editing
	Press PLAY ( 3) on this VCR, and start playback

on the other component at the same time.

cDuring Insert Editing mode ( and light up

on the front display panel.)

cDuring A/V Dubbing mode ( and blink on the front display panel.)

cWhen the counter reading becomes “0:00:00”, editing automatically stops, and the VCR starts normal playback.

5	Select video input terminal
	Follow the procedure described on pages 38 and
	42.
	When using S VIDEO terminal, set “FRONT AUX
	INPUT” (or “REAR AUX INPUT” if you use the
	connectors on the rear) to “S-VIDEO”.
	When using VIDEO terminal, set “FRONT AUX
	INPUT” (or “REAR AUX INPUT”) to “VIDEO”.

6	Select edit mode
	Set the edit mode to “ON” for the VCRs if such a
	mode is equipped.
	c On this VCR, set “PICTURE CONTROL” to
	“EDIT” by following the procedure described
	on pages 38 and 39.

7	Locate end point
	1	Press PLAY ( 3) to start playback.
	2	Press PAUSE ( 8 ) when you find the end of
		the scene for which you want to edit.
	3	Press C. RESET so that the counter reading
		becomes “0:00:00”.

NOTE:

You can also use REW ( ) or SHUTTLE ring to locate the end point (See “Special Effect Playback”: Z pg. 28) .

To stop editing any time during recording.

Press STOP ( 7 ) on the Remote or STOP/EJECT ( 7 / 0 ) on the front panel.

NOTES:

c Be sure to select “AUTO” for “PICTURE CONTROL” (or “NORM” when “VIDEO CALIBRATION” is set to “OFF”) after you finish editing the tapes (Z pg. 38 and 39).

c Editing cannot be performed on a tape with its record safety tab removed.

c The recording speed (SP/EP) is determined by the previous recording to be replaced. If the recording speed changes on the tape to be edited while editing the tape, the inserted picture will be distorted where the recording speed changes.

c When you edit a tape, a small portion of the recording preceding to the editing start point will be erased from the edited tape.

HR-S4800U/S3800U-EN44-53 49 00.1.31, 10:03 AM