PRESS (8=DAILY, 9=WEEKLY STOP+/– = STOP TIME, SP/EP)
PRESS (OK) TO END

1

2

3

 

NUMBER

"9"

 

 

 

 

 

 

 

 

2

 

 

4

5

6

 

 

 

NUMBER "8" 7

8

 

9

 

 

0

 

TIMER

CANCEL

 

 

4

 

 

 

 

 

 

 

STOP+/–

 

 

 

 

PROG.

1

 

 

 

 

 

 

 

SP/EP

 

 

 

3

OK

ATTENTION

If there is a conflict in the timer schedule and one program overlaps with another, only the parts shown below in gray will be recorded.

Pattern 1: The program with the lower program number will be recorded.

10:00

11:00

12:00

Program 1

 

CH10

 

 

 

 

Program 2

 

 

 

 

 

 

Not recorded

 

 

CH40

 

 

 

Pattern 2: The program that is broadcast earlier will be recorded.

10:00

11:00

12:00

Program 1

 

CH10

 

 

 

 

Program 2

 

 

 

Not recorded

CH40

 

 

Pattern 3: The program that is broadcast earlier will be recorded, followed by the remaining portion of the other program.

10:00

11:00

12:00

Program 1

 

CH10

 

 

 

 

Program 2

 

CH40

 

 

 

Not recorded

 

 

 

 

 

 

E

 

N

 

47

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CHECK PROGRAM DATA

 

 

 

The PlusCode number you

 

PROGRAM 1

 

 

entered and the matching

(VCR PLUS+ 12345678)

 

 

 

5 Timer-Recording informa-

START

 

 

STOP

 

 

 

8:00PM

= 10:00PM

 

 

tion is displayed on the

DATE

 

 

CH

 

 

Program screen. Check to

12/24/98

 

 

12 SP

 

 

make sure it’s accurate.

THU

 

 

 

 

 

 

 

To change the stop time, press STOP +/–.

To timer-record daily or weekly serials, press DAILY (NUMBER “8”) or WEEKLY (NUMBER “9”). “DAILY” or “WEEKLY” appears on the Program screen.

Pressing the button again makes each corresponding display disappear.

If you made a mistake, press CANCEL to access the VCR Plus+ screen again and input the correct PlusCode number.

If the PlusCode number you inputted is incorrect, "ERROR" may appear on the screen to advise you of the error. This happens when the PlusCode number is for a program which has already passed. "ERROR" is displayed for about 5 seconds and the VCR Plus+ screen reappears.

SET TAPE SPEED

6 Press SP/EP.

RETURN TO NORMAL

SCREEN

7 Press PROG. or OK. "PROGRAM COMPLETED" appears on the screen for about 5 seconds, then normal screen appears.

ENGAGE TIMER MODE

8 Press TIMER. The VCR turns off automatically and "ä" is displayed on the display panel.

IMPORTANT

If you have moved to a different area or if a broadcasting station's channel number has been changed, the wrong VCR or CABLE CH number will be displayed on the VCR Plus+ Program screen in step 5. When this happens, set the correct the Guide Channel number for that station. (pg. 48, "VCR Plus+ Setup")

NOTES:

To disengage the timer before recording starts, press TIMER again. Pressing once more re-engages it.

In case of a power failure after programming, the VCR’s memory backup keeps your selections for approximately 10 minutes.

When timer-recording cable channels received through a Cable Box, be sure to keep the Cable Box set to ON.

Page 47
Image 47
JVC HR-S9500U manual Engage Timer Mode