Troubleshooting
Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC service center.
PROBLEM |
| POSSIBLE CAUSE |
|
| SOLUTION |
| |||
The display does not light up. | The power cord is not plugged in or the | Plug the power cord into an AC outlet and/ |
| ||||||
|
| POWER switch is press to set in the Ñ | or press |
| POWER to set it in the _ON |
| |||
|
|
|
| ||||||
|
|
|
| ||||||
| OFF position. | position. |
| ||||||
|
|
|
|
|
|
|
|
|
|
No sound from speakers. | Speaker signal cables are not connected. | Check speaker wiring and |
| ||||||
|
|
| reconnect if necessary. |
| |||||
|
|
|
|
|
|
|
|
|
|
| The SPEAKERS 1 and 2 buttons is not set | Press SPEAKERS 1 and 2 to set it in the |
| ||||||
| correctly. | _ON position. |
| ||||||
|
|
|
|
|
|
|
|
|
|
| An incorrect source is selected. | Select the correct source. |
| ||||||
|
|
|
| ||||||
“OVERLOAD” starts flashing on the | Speakers are | Rotate the MASTER VOLUME control |
| ||||||
display. | volume. | counterclockwise three or four times then |
| ||||||
|
|
| press STANDBY/ON |
| on the front |
| |||
|
|
|
|
| |||||
|
|
|
|
| |||||
|
|
| panel. |
| |||||
|
|
| If “OVERLOAD” does not disappear, |
| |||||
|
|
| unplug the AC power cord, then plug it |
| |||||
|
|
| back again. |
| |||||
|
|
| Do not use the remote control when |
| |||||
|
|
| “OVERLOAD” is shown on the display. |
| |||||
|
|
|
|
|
|
|
|
|
|
English
Speakers are
Press STANDBY/ON 
on the front panel then check the speaker wiring. If “OVERLOAD” does not disappear, unplug the AC power cord, then plug it back again.
Do not use the remote control when “OVERLOAD” is shown on the display. If speaker wiring is not short circuited, contact your dealer.
| Sound from one speaker only. |
|
| Speaker signal cables are not connected | Check speaker wiring and reconnect if |
|
|
|
| properly. | necessary. |
|
|
|
|
|
|
|
|
|
| The balance is set to one extreme. | Adjust the balance properly (see page 12). |
|
|
|
|
|
|
| Continuous hiss or buzzing during FM |
|
| Incoming signal is too weak. | Connect an outside FM antenna or contact |
| reception. |
|
|
| your dealer. |
|
|
|
|
|
|
|
|
|
| The station is too far away. | Select a new station. |
|
|
|
|
|
|
|
|
|
| An incorrect antenna is used. | Check with your dealer to be sure you |
|
|
|
|
| have the correct antenna. |
|
|
|
|
|
|
|
|
|
| Antennas are not connected properly. | Check connections. |
|
|
|
|
|
|
| Occasional cracking noise during FM |
|
| Ignition noise from automobiles. | Move the antenna farther from automobile |
| reception. |
|
|
| traffic. |
|
|
|
|
|
|
| Howling during record playing. |
|
| Your turntable is too close to speakers. | Move speakers away from the turntable. |
|
|
|
|
|
|
| Remote control does not work. |
|
| There is an obstruction in front of the | Remove the obstruction. |
|
|
|
| remote sensor on the receiver. |
|
|
|
|
|
|
|
|
|
|
| Batteries are weak. | Replace batteries. |
|
|
|
|
|
|
40
