Getting Started, General, Locations | JVC RX-554RBK specs

English

Getting Started

This section explains how to connect stereo components and speakers to the receiver, and how to connect the power supply.

Before Installation

General

•Be sure your hands are dry.

•Turn the power off to all components.

•Read the manuals supplied with the components you are going to connect.

Locations

•Install the receiver in a location that is level and protected from moisture.

•The temperature around the receiver must be between –5˚ and 35˚ C (23˚ and 95˚ F ).

•Make sure there is good ventilation around the receiver. Poor ventilation could cause overheating and damage the receiver.

Handling the receiver

•Do not insert any metal object into the receiver.

•Do not disassemble the receiver or remove screws, covers, or cabinet.

•Do not expose the receiver to rain or moisture.

Checking the Supplied Accessories

Check to be sure you have all of the following items, which are supplied with the receiver.

The number in the parentheses indicates quantity of the pieces supplied.

•Remote Control (1)

•Batteries (2)

•AM (MW/LW) Loop Antenna (1)

•FM Antenna (1)

If anything is missing, contact your dealer immediately.

3

Image 8

JVC RX-554RBK manual Getting Started, General, Locations, Handling the receiver

Contents

RX-554RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-554RBK Table of Contents Front Panel Remote ControlParts Identification Getting Started GeneralLocations Handling the receiver Connecting the FM and AM MW/LW Antennas Using the Supplied FM AntennaUsing the Standard Type Connector Not supplied FM Antenna Connections Connecting the front speakers Connecting the rear and center speakersConnecting the Speakers Getting Started About the speaker impedance 16 ohm Connecting Other Components Audio component connectionsVideo component connections If your audio components have a Compu LINK-3 terminals Putting Batteries in the Remote Control Connecting the Power CordTo shut off the power completely From the remote control Turning the Power On and Off StandbyBasic Operations On the front panel From the remote control only Adjusting the VolumeOn the front panel only Selecting the Front Speakers Listening with Headphones To listen with only headphonesBasic Operations Recording a Source Basic Settings Adjusting the Front Speaker Output BalanceListening at Low Volume Loudness Using the Sleep Timer Basic Settings When the shut-off time comesTo cancel the Sleep Timer Selecting the Center Speaker Size To store the sound settings To recall the sound settingsTo cancel the One Touch Operation function One Touch Operation Tuning in Stations Manually Using Preset TuningTo store the preset stations Receiving Radio Broadcasts Press 10 keys to select a preset channel number To cancel a stored preset stationTo tune in a preset station Selecting the FM Reception Mode Using the RDS Radio Data System to Receive FM StationsReceiving Radio Broadcasts Press TUNER/BAND so that the Control %/ Þ/ @ What Information Can RDS Signals Provide? To search for a program using the PTY codes Searching for a Program by PTY CodesPress PTY Search again To continue searching after the first stop Press PTY Search while listening to an FM station Display gives you the PTY codes described on Descriptions of the PTY codes Switching to a Broadcast Program of Your Choice Temporarily Receiver enters EON standby modeTraffic Announcement in your area News To stop listening to the program selected by EON Press EON so that the program type TA/NEWS/INFO goes To cancel the preset SEA mode Using the Preset SEA ModesSelecting Your Favorite SEA Mode Using the Preset SEA Modes Press SEA Preset to select the effect level On JVC 3D Phonic mode On the DAP modeActivating the Surround Sounds On surround modes Using JVC 3D-PHONIC Modes Activating the Surround Sounds3DACTION 3DTHEATR Press Control @ / #to adjust the effect level To cancel the 3D-PHONIC modeMark Press Effect to select the effect level Using the DAP Modes PavilionHall Gives clear vocal and the feeling of a concert hall Press Control @/ #to adjust the rear speaker output level To cancel the DAP modeSelect OFF in step DAP indicator goes off from the display Press Rear +/- to adjust the rear speaker output level Select Prologic or Theater Select Phantom for center mode Select 3CHLOGIC Select Normal or Wide for center modeSpeaker Arrangements for Surround Modes This case Preparing for Surround Modes TheaterPrologic 3CHLOGIC Press Control @/ # to select the center mode DelayWide Normal If necessary, adjust the speaker output balance as follows Delay 1 Delay 2 Delay Press Effect to adjust the effect level Press Test to start checking the speaker outputBalance Press Test again to stop the test tone Using Surround Modes To cancel surround modeFrom the front panel Work for selecting the surround/DAP/3D-PHONIC Modes Compu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverAutomatic Source Selection Synchronized Recording To operate JVC audio components using this remote control Operating Other Components Operating Other Components Standby/On section Troubleshooting Problem Possible Cause Solution Specifications Amplifier General FM tuner IHFAM MW/LW tuner EN, GE, FR, NL, SP, IT