Table of Contents | JVC RX-554RBK instruction

English

Table of Contents

Parts Identification	2
Getting Started	3
Before Installation	3
Checking the Supplied Accessories	3
Connecting the FM and AM (MW/LW) Antennas	4
Connecting the Speakers	5
Connecting Other Components	7
Connecting the Power Cord	8
Putting Batteries in the Remote Control	8
Basic Operations	9
Turning the Power On and Off (Standby)	9
Selecting the Source to Play	9
Adjusting the Volume	10
Selecting the Front Speakers	10
Muting the Sound	10
Recording a Source	11
Listening with Headphones	11
Basic Settings	12
Adjusting the Front Speaker Output Balance	12
Listening at Low Volume (Loudness)	12
Using the Sleep Timer	12
Selecting the Center Speaker Size	13
One Touch Operation	14
About the One Touch Operation	14
Using the One Touch Operation	14
Receiving Radio Broadcasts	15
Tuning in Stations Manually	15
Using Preset Tuning	15
Selecting the FM Reception Mode	17
Using theRDS (Radio Data System) to Receive FM Stations	17
What Information Can RDS Signals Provide?	18
Searching for a Program by PTY Codes	19
Switching to a Broadcast Program of Your Choice Temporarily	22
Using the Preset SEA Modes	24
Selecting Your Favorite SEA Mode	24
Activating the Surround Sounds	26
Using JVC 3D-PHONIC Modes	27
Using the DAP Modes	29
Speaker Arrangements for Surround Modes	31
Preparing for Surround Modes	32
Using Surround Modes	36
COMPU LINK Remote Control System	37
Operating Other Components	38
Troubleshooting	40
Specifications	41

1

Image 6

JVC RX-554RBK manual Table of Contents

Contents

RX-554RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-554RBK Table of Contents Remote Control Parts IdentificationFront Panel Locations Getting StartedGeneral Handling the receiver Using the Standard Type Connector Not supplied Connecting the FM and AM MW/LW AntennasUsing the Supplied FM Antenna FM Antenna Connections Connecting the Speakers Connecting the front speakersConnecting the rear and center speakers Getting Started About the speaker impedance 16 ohm Video component connections Connecting Other ComponentsAudio component connections If your audio components have a Compu LINK-3 terminals Connecting the Power Cord To shut off the power completelyPutting Batteries in the Remote Control Basic Operations From the remote controlTurning the Power On and Off Standby On the front panel On the front panel only From the remote control onlyAdjusting the Volume Selecting the Front Speakers Basic Operations Listening with HeadphonesTo listen with only headphones Recording a Source Listening at Low Volume Loudness Basic SettingsAdjusting the Front Speaker Output Balance Using the Sleep Timer To cancel the Sleep Timer Basic SettingsWhen the shut-off time comes Selecting the Center Speaker Size To cancel the One Touch Operation function To store the sound settingsTo recall the sound settings One Touch Operation To store the preset stations Tuning in Stations ManuallyUsing Preset Tuning Receiving Radio Broadcasts To cancel a stored preset station To tune in a preset stationPress 10 keys to select a preset channel number Receiving Radio Broadcasts Selecting the FM Reception ModeUsing the RDS Radio Data System to Receive FM Stations Press TUNER/BAND so that the Control %/ Þ/ @ What Information Can RDS Signals Provide? Press PTY Search again To search for a program using the PTY codesSearching for a Program by PTY Codes To continue searching after the first stop Press PTY Search while listening to an FM station Display gives you the PTY codes described on Descriptions of the PTY codes Traffic Announcement in your area Switching to a Broadcast Program of Your Choice TemporarilyReceiver enters EON standby mode News To stop listening to the program selected by EON Press EON so that the program type TA/NEWS/INFO goes Using the Preset SEA Modes Selecting Your Favorite SEA ModeTo cancel the preset SEA mode Using the Preset SEA Modes Press SEA Preset to select the effect level Activating the Surround Sounds On JVC 3D Phonic modeOn the DAP mode On surround modes 3DACTION Using JVC 3D-PHONIC ModesActivating the Surround Sounds 3DTHEATR Mark Press Control @ / #to adjust the effect levelTo cancel the 3D-PHONIC mode Press Effect to select the effect level Hall Using the DAP ModesPavilion Gives clear vocal and the feeling of a concert hall Select OFF in step DAP indicator goes off from the display Press Control @/ #to adjust the rear speaker output levelTo cancel the DAP mode Press Rear +/- to adjust the rear speaker output level Speaker Arrangements for Surround Modes Select Prologic or Theater Select Phantom for center modeSelect 3CHLOGIC Select Normal or Wide for center mode This case Prologic Preparing for Surround ModesTheater 3CHLOGIC Wide Press Control @/ # to select the center modeDelay Normal If necessary, adjust the speaker output balance as follows Delay 1 Delay 2 Delay Balance Press Effect to adjust the effect levelPress Test to start checking the speaker output Press Test again to stop the test tone From the front panel Using Surround ModesTo cancel surround mode Work for selecting the surround/DAP/3D-PHONIC Modes Automatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Synchronized Recording To operate JVC audio components using this remote control Operating Other Components Operating Other Components Standby/On section Troubleshooting Problem Possible Cause Solution Specifications Amplifier FM tuner IHF AM MW/LW tunerGeneral EN, GE, FR, NL, SP, IT