Turning off the power with the Sleep Timer
You can fall asleep while listening to
From the remote control ONLY:
Press SLEEP repeatedly.
•Each time you press the button, the
SLEEP indicator
ANALOG | AUTO SURR | SLEEP |
LR
S.WFR
10min
20min
30min
40min 
50min
60min 
OFF (canceled) 
90min
80min
70min
When the
The receiver turns off automatically.
To check or change the remaining time until the
Press SLEEP once.
The remaining time (in minutes) until the
• To change the
To cancel the Sleep Timer:
Press SLEEP repeatedly so that “SLEEP OFF” appears on the display. (The SLEEP indicator goes off.)
•The Sleep Timer is also canceled when you turn off the receiver.
Making sounds natural
JVC’s CC (Compression Compensative) Converter eliminates jitter and ripples, achieving a drastic reduction in digital distortion by processing the digital music data in 24
Press CC CONVERTER repeatedly.
•Each time you press the button, the mode changes as follows:
CC CNVRTR 1: Select when playing back an analog source or a digital source with non compressed digital sound signal (Linear PCM).
The CC CONVERTER 1 indicator lights
up on the display.
CCCNVRTR 2: Select when playing back a source with compressed digital sound signal (Dolby
Digital or DTS).
The CC CONVERTER 2 indicator lights up on the display.
CC CNVRTR OFF: Select when not using the CC Converter.
Basic adjustment of auto memory
This receiver memorizes sound settings for each source:
•when you turn off the power, and
•when you change the source.
When you change the source, the memorized settings for the newly selected source are automatically recalled.
The following can be stored for each source:
•Audio input setting (see page 20)
•Midnight mode (see page 31)
•Volume level for each source when One Touch Operation is set to “ONE TOUCH OP: ON” (see page 32)
•Speaker output level (see page 36)
•Digital equalization pattern (see page 37)
•Bass boost (see page 37)
•Input attenuator mode (see page 37)
•Surround/DSP mode selection (see page 45)
NOTE
If the source is “FM” or “AM,” you can assign a different setting for each band.
Signal and speaker indicators on the display
Signal indicators |
|
|
|
| Speaker indicators | ||||||
L | C | R |
|
|
|
|
| L | C | R | |
S.WFR | LFE | ANALOG | DUAL MONO | AUTO SURR | S.WFR | LFE | |||||
LS | S | RS | DIGITAL AUTO | L | C R | HEADPHONE | LS | S | RS | ||
LINEAR PCM | S.WFR LFE | PL | x | ||||||||
SB | SB | SB | DIGITAL | LS | S RS | NEO : 6 | DSP | SB | SB | SB | |
96 / 24 | |||||||||||
SB | SB SB | ||||||||||
VIRTUAL SB | |||||||||||
|
|
|
|
|
|
| |||||
The signal indicators light up as follows:
L:• When digital input is selected: Lights up when the left channel signal comes in.
•When analog input is selected: Always lights up.
R:• When digital input is selected: Lights up when the right channel signal comes in.
•When analog input is selected: Always lights up.
C:Lights up when the center channel signal comes in. LS: Lights up when the left surround channel signal comes
in.
RS: Lights up when the right surround channel signal comes
in.
S:Lights up when monaural surround signal comes in. SB: Lights up when the surround back channel signal
comes in.
LFE: Lights up when the LFE channel signal comes in.
NOTES
•When “A MULTI” is selected in the audio input setting (see page 20), all the signal indicators except “SB,” “S,” and “LFE” light up.
•When playing back
The speaker indicators light up as follows:
•The subwoofer indicator ( S.WFR ) lights up when “SUBWOOFER” is set to “SUBWOOFER: YES.” For details, see page 28.
•The other speaker indicators light up only when the corresponding speaker is set to “SMALL” or “LARGE,” and also when required for the current playback.
22
