Alternateconnection, External Ground connector | Kenmore 3405602

ALTERNATECONNECTION:

If local codes do not permit the

connection of a frame-grounding

conductor to the neutral wire:

STEP 1. Make sure the power supply to the dryer is off.

STEP 2. Make sure the power supply cord or direct wire cable is in place (see steps 1-3 on pages 12-13 for power cord connections or steps 1-3 on pages 13-14 for ,direct wire connection).

STE=P 3, Remove the neutral grounding wire (green/yellow wire) from external grounding connector screw. Loosen or remove terminal block screws. Connect

neutral grounding wire and the neutral wire (white or center) of power supply cord or direct wire cable under the center screw of the terminal block.

External

ground connector

STEP 4, Connect the other two wires to outer terminal block screws. Tighten all terminal block screws firmly.

STEP 5, Tighten the strain relief screws.

STEP 6, Insert tab of terminal block

cover into slot of the dryer rear panel. Secure cover with hold-down screw.

STEP 7, Connect separate copper grounding wire from external ground connector to an adequate ground. If codes permit and a separate grounding wire is used, it is recommended that a qualified electrician determine that the grounding path is adequate.

Proceed with Exhaust Installation. See "CONNECT EXHAUST" on

page 19.

Neutral groundingwire (green/yellow)

Groundingpath determinedbya qualiliedelectrician

Alternate 3-Wire Connection with

External-Grounding Conductor

15

Image 15

Kenmore 3405602 owner manual Alternateconnection, Conductor to the neutral wire, External Ground connector

Contents

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A OwnersManual Installation Instructions Keep this book and your Sears Full 1-YEAR Warranty on Mechanical and Electrical Parts Your safety and the safety of others is very important Your Safety is Important to US Installation Overview Select LocationParts Needed If making a direct wire connection Tools Needed Parts Needed Optional depending Connect Exhaust pgs Tools Needed Parts Needed Select Location for Your Dryer Standard Installation Product Dimensions Recessed AREA/CLOSET Installation Instructions Install Leveling Legs Electrical Connection Options If Your Home Has Wire electrical ReceptacleIt is your responsibility Quincy, Massachusetts NEI THREE-WIREELECTRICAL Exlernal ground ConnectorWhite neutral wire Wire Connection with Exhaust Conductor to the neutral wire External Ground connectorAlternateconnection Neutral III. Make FOUR-WIREFour-wire receptacle Nema Type 14-30R Electrical Connection to Receptacle Neutral WireGreenwire Powersupply IV. FOUR-WIRE Electrical Connection Direct Wire BarecopperwireNeutral Whiteneutralwire Route the Vent Typical installations for left or right side exhausting Determine Vent Length Exhaust Hood TypeStep Flexible metalvent IDryerDucttape & clamp Offset Connections with Close Clearances Loop SystemPeriscope System Final Steps Review Installation Starting Your Dryer STOPPING/RESTARTINGYour Dryer Touch UP Cycle Cycle DescriptionAuto DRY Cycle Timed DRY Cycle Cottons and Linens FABRIC/TEMPERATURE Control Delicate Fabrics Using AIR DRY/AIR FluffTo use AIR Fluff AIR Fluff Cool Down Push to Start Button Using Wrinkle Guard WrinkleguardLint Alert HEATEDDR.RACK Preparing Clothes For Drying Choosing Load SizesSuper Capacity Plus Dryers Drying Tips Using Dryer FABRICSOFrENERS Cleaning Your Dryer ExteriorInterior To wash Cleaning the Lint ScreenTo clean Wash Lint Screen As Needed Checking for AIR Flow Obstruction To remove accumulated lint from Inside the dryerRemoving Accumulated Lint Changing the Drum Light Moving CareVacation Care Not Drying Wrinkled ContLoad is overdried Stains on Load For more information, call We Service What We SellSears Maintenance Agreement Kenmore DryersPage 8F,eLR8