Kenwood DPF-R4010 Specifications, Fcc Warning, Format, System, Compact disc digital audio system

Specifications

CD-206/204/203/DPF-R6010/R4010/R3010 (En)

CD-206/DPF-R6010 CD-204/203/DPF-R4010/3010

26

[ Format ]
System	Compact disc digital audio system
Laser		Semiconductor laser
[ D/A Convertors ]
D/A Conversion		1 Bit (D.R.I.V.E.)
Oversampling		8 fs (352.8 kHz)
[ Audio ]
Frequency response		4 Hz – 20 kHz, ±0.5 dB
Signal to noise ratio		More than 100 dB
Dynamic range		More than 95 dB
Total harmonic distortion + noise
..............................................		Less than 0.005% (at 1 kHz)
Wow & flutter		Unmeasurable Limit
Output level/impedance		(Max.) 2 V/0.3 kΩ
Variable
Digital output		0.5 V p-p / 75 Ω
Coaxial
Optical		–15 dBm – –21 dBm
		(Wave length 660 nm)
Headphone output (Max.)		.............................. 20 mW (32 Ω)
[ General ]
Power consumption		14 W
Dimensions		W: 440 mm (17-5/16")
		H : 125 mm (4-15/16")
		D : 397 mm (15-5/8")
Weight (Net)		5.0 kg (11.0 lb)

[ Format ]
System	Compact disc digital audio system
Laser		Semiconductor laser
[ D/A Convertors ]
D/A Conversion		1 Bit
Oversampling		8 fs (352.8 kHz)
[ Audio ]
Frequency response		4 Hz – 20 kHz, ±0.5 dB
Signal to noise ratio		More than 95 dB
Dynamic range		More than 95 dB
Total harmonic distortion + noise
.............................................	Less than 0.008% (at 1 kHz)
Wow & flutter		Unmeasurable Limit
Output level/impedance		2 V/0.8 kΩ
Fixed (CD-203/DPF-R3010)
Variable (CD-204/DPF-R4010)		(Max.) 2 V/0.3 kΩ
Headphone output (Max.)		20 mW (32 Ω)
(CD-204/DPF-R4010 only)
[ General ]
Power consumption		13 W
Dimensions		W: 440 mm (17-5/16")
		H : 125 mm (4-15/16")
		D : 397 mm (15-5/8")
Weight (Net)		5.0 kg (11.0 lb)

1. KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice.

Notes 2. The full performance may not be exhibited in an extremely cold location (under a water-freezing temperature).

For the U.S.A.

FCC WARNING:

This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

–Reorient or relocate the receiving antenna.

–Increase the separation between the equipment and receiver.

–Connect the equipment into an outlet on a circuit different from that to which the receiver in connected.

–Consult the dealer or an experienced radio/TV technician for help.