6 COMMUNICATING
■Storing CW Messages
The two modes available for storing messages are Character mode and Real Time mode. Each message may be as long as you want provided that the total of all four messages including spaces does not exceed about 220 characters. You must use the internal keyer to use the message storage function. If you happen to turn OFF the power while storing a message, the last letters input may be deleted. You cannot store messages if you are operating split mode (transmit mode different than receive mode).
Using Character mode (default):
This mode uses message memory most efficiently. Each Morse character uses one byte of memory. When you play back your recorded messages, they will be sent with precise intercharacter and interword spacing.
1 Press [CH 1] or [CH 2] or [CH 3] or [CH 4] for approximately two seconds until you hear a tone.
¥The keyer will send the letter ÒCÓ. This stands for Character mode.
¥If the keyer sends ÒRÓ (for Real Time), you must switch to Character mode by using the Function mode {page 36}.
2Send the first word of your message then pause.
¥The keyer will send the letter ÒIÓ indicating it has accepted your word.
3Repeat Step 2 pausing to hear the ÒIÓ before sending the next word until all words of your message are entered.
¥If you make a sending mistake, send seven or more dits to signal an error, then wait for the keyer to respond with the last correct word. You can then send the next word that you want in the message. Each time that you send the
4Press the same button as pressed in Step 1.
Using Real Time mode:
Real Time mode captures exactly what you send without altering your spacing. This mode cannot use Embedded Functions {page 37}. Also, you cannot correct words by using the
Before beginning, switch to Real Time mode by using the Function mode {page 36}.
1Press [CH 1] or [CH 2] or [CH 3] or [CH 4] for approximately two seconds until you hear a tone.
¥The keyer will send the letter ÒRÓ. This stands for Real Time mode.
2Send your entire message.
3Press the same button as pressed in Step 1.
¥Message recording begins at the moment the first character is sent, and continues until this step is completed. Any pause between the last character and this step is recorded as part of the message.
■CW Message Playback
Messages may be transmitted using the VOX function or manual TX/RX switching. The procedure below uses the VOX function. Simply tap the paddle at any time to stop a message while it is playing back, or press any two of [CH 1], [CH 2], [CH 3], or [CH 4] to stop the message without transmitting an extra character. Resuming playback after such an interruption replays the message from the beginning.
Switching OFF the power while playing back a message could delete the message. You cannot play back messages if you are operating split mode (transmit mode different than receive mode).
To check a message without transmitting:
1 Press [VOX] to switch OFF the VOX function.
2 Press the memory channel button ([CH 1] or [CH 2] or [CH 3] or [CH 4]) that contains the message that you want to check.
¥The message plays.
¥To play back up to 8 messages, press the corresponding memory channel buttons in sequence during playback.
To transmit a message:
1Press [VOX] to switch ON the VOX function.
2Press the memory channel button ([CH 1] or [CH 2] or [CH 3] or [CH 4]) that contains the message that you want to transmit.
¥The message is transmitted.
¥To transmit up to 8 messages, press the corresponding memory channel buttons in sequence during playback.
The ÒQÓ Function command {page 36} allows you to queue several messages to form a longer message.
Example:
¥ÒQÓ Function status: ON
¥Channel 1 contents: ÒCQÓ
¥Channel 2 contents: Òde DFØTKÓ
In this example, pressing the button sequence [CH 1], [CH 1], [CH 1], [CH 2] would send ÒCQ CQ CQ de DFØTKÓ.
34
