●APPENDICES
Command | Function |
|
|
FB | Sets or reads VFO B frequency. |
|
|
FD | Reads RX filter dot display. |
|
|
FR | Sets RX (VFO A/B, memory channel). |
|
|
FS | Fine function (OFF/ON) |
|
|
FT | Sets TX (VFO A/B, memory channel). |
|
|
FW | Sets or reads filter bandwidth. For SSB |
| and AM, sets or reads the |
| |
|
|
GT | Sets or reads AGC time constant. |
ID | Reads model number of the transceiver. |
IF | Reads status of the transceiver. |
IS | Sets or reads IF shift. For SSB and AM, |
| sets or reads the |
| frequency. |
KS | Sets or reads keying speed while using |
| the KY command. |
KY | Converts input characters into Morse |
| code. |
LK | Sets or reads Lock (OFF/ON). |
|
|
LM | DRS recording |
|
|
MC | Sets or reads memory channels. |
|
|
MD | Sets or reads modes. |
MG | Sets or reads MIC gain. |
ML | Sets or reads transmit monitor level. |
MN | Sets or reads Transmit Monitor |
| (OFF/ON). |
|
|
MR | Reads memory. |
MW | Writes into memory. |
MX | Sets or reads AIP (OFF/ON). |
NB | Sets or reads Noise Blanker (OFF/ON). |
NL | Sets or reads Noise Blanker level. |
NR | Sets or reads Noise Reduction (OFF/ON). |
NT | Sets or reads Notch Filter. |
PB | DRS playback. |
|
|
PC | Sets or reads transmit power. |
PL | Sets or reads Speech Processor level. |
PR | Sets or reads Speech Processor |
| (OFF/ON). |
PS | Sets or reads power (OFF/ON). |
RA | Sets or reads RF ATT (attenuator). |
RC | Clears RIT frequency. |
RD | Lowers RIT frequency. |
RG | Sets or reads RF gain. |
|
|
Command | Function | |
|
| |
RM | Selects a meter function or reads | |
meter values. | ||
| ||
RT | Sets or reads RIT (OFF/ON). | |
RU | Raises RIT frequency. | |
|
| |
RX | Selects receive mode. | |
|
| |
SC | Sets or reads Scan (OFF/ON). | |
|
| |
SD | Sets or reads Semi | |
SM | ||
|
| |
SQ | Sets or reads squelch level. | |
|
| |
SR | Resets the transceiver. | |
|
| |
TX | Selects transmit mode. | |
UP | MIC UP function | |
VD | Sets or reads VOX delay time. | |
VR | Triggers the Voice Synthesizer for | |
| message output. | |
|
| |
VX | Sets VOX (OFF/ON). | |
XT | Sets or reads XIT (OFF/ON). |
In addition to the Answer Command, the transceiver can send the following error messages:
Error | Reason for Error | |
Message | ||
| ||
?; | • Command syntax was incorrect. | |
| • Command was not executed due to | |
| the current status of the transceiver | |
| (even though the command syntax | |
| was correct). | |
| Note: Occasionally this message may not | |
| appear due to microprocessor transients in the | |
| transceiver. | |
|
| |
E; | A communication error occurred such | |
| as an overrun or framing error during a | |
| serial data transmission. | |
|
| |
O; | Receive data was sent but processing | |
| was not completed. | |
|
|
1Do not use the control characters 00 to 1Fh since they are either ignored or cause a Ò?Ó answer.
2Program execution may be delayed while turning the Tuning control rapidly.
3Receive data is not processed if the frequency is entered from the keypad.
86