Kenwood TS-870S instruction manual Appendices

APPENDICES ●

FR			FT				FUNCTION RX, FUNCTION TX
																				Parameter	Format	Parameter function
Function	Sets RX/TX (VFO A/B, memory channel).																			P1	3	FUNCTION
		Set		1			2	3	4	5	6	7	8	9	10	11	12	13	14
Input						F	R/T	P1	;
		Read		1			2	3	4	5	6	7	8	9	10	11	12	13	14
					F		R/T	;
Output		Answer		1			2	3	4	5	6	7	8	9	10	11	12	13	14
						F	R/T	P1	;

FS			FINE STEP
																				Parameter		Format	Parameter function
Function	Fine function OFF/ON																			P1		1	FINE OFF/ON
		Set		1		2	3	4	5	6	7	8	9	10	11	12	13	14
Input					F	S	P1	;
		Read		1		2	3	4	5	6	7	8	9	10	11	12	13	14
					F	S	;
Output		Answer		1		2	3	4	5	6	7	8	9	10	11	12	13	14
					F	S	P1	;
FW			FILTER WIDTH
																				Parameter		Format	Parameter function
Function	Sets or reads filter bandwidth. For SSB and AM, sets or reads the																			P1		38	FILTER WIDTH
	high-pass filter cut-off frequency.
																				Note:
																				Allowable data(units of 10 Hz):
				1		2	3	4	5	6	7	8	9	10	11	12	13	14
		ReadSet																		SSB:	0, 5, 10, 20, 30, 40, 50, 60, 80, 100
Input					F	W			P1		;									CW:	5, 10, 20, 40, 60, 100
																				FSK:	25, 50, 100, 150
				1		2	3	4	5	6	7	8	9	10	11	12	13	14
																				FM:	500, 600, 800, 1000, 1200, 1400
					F	W	;													AM:	0, 10, 20, 50
Output		Answer		1		2	3	4	5	6	7	8	9	10	11	12	13	14
					F	W			P1		;
GT		AUTO GAIN CONTROL TIME CONSTANT
																			Parameter			Format	Parameter function
Function	Sets or reads AGC time constant.																			P1		39	AGC TIME CONSTANT
		Set		1		2	3	4	5	6	7	8	9	10	11	12	13	14
Input					G	T		P1		;
		Read		1		2	3	4	5	6	7	8	9	10	11	12	13	14
					G	T	;
Output		Answer		1		2	3	4	5	6	7	8	9	10	11	12	13	14
					G	T		P1		;

ID IDENTIFICATION

Function															Parameter	Format	Parameter function
	Reads Model number of the transceiver.														P1	16	MODEL NUMBER
	ReadSet	1	2	3	4	5	6	7	8	9	10	11	12	13	14
Input		1	2	3	4	5	6	7	8	9	10	11	12	13	14
Output	Answer	I	D	;
		1	2	3	4	5	6	7	8	9	10	11	12	13	14
		I	D		P1		;

IF				INFORMATION
Function																						Parameter		Format	Parameter function
																						P3		5	RIT/XIT FREQUENCY
	Reads status of the transceiver.																					P1		4	FREQUENCY
																						P2		–	NOT USED
				command	1	2		3		4		5	6	7	8	9	10	11	12	13	14	P4		1	RIT OFF/ON
commands		Set			1	2		3		4		5	6	7	8	9	10	11	12	13	14	P9		2	MODE
																						P5		1	XIT OFF/ON
					15	16		17		18		19	20	21	22	23	24	25	26	27	28	P6		–	NOT USED
																						P7		7	MEMORY CHANNEL
Input				command																		P8		11	TX/RX
		Read			I		F	;														P10		3	FUNCTION
																						P11		1	SCAN OFF/ON
					15	16		17		18		19	20	21	22	23	24	25	26	27	28
																						P12		1	SPLIT OFF/ON
																						P13		1	TONE OFF/ON
commandsOutput			commandAnswer		1	2		3		4		5	6	7	8	9	10	11	12	13	14	P14		14	TONE NUMBER
					P8	P9 P10 P11 P12 P13								P14			;					P15		–	NOT USED
					I		F							P1
					15	16		17		18		19	20	21	22	23	24	25	26	27	28
														P3			P4	P5		P7
					29	30		31		32		33	34	35	36	37	38	39	40	41	42
IS				IF SHIFT
																						Parameter		Format	Parameter function
Function	Sets or reads IF shift. For SSB and AM, sets or reads the low-pass filter																					P2		41	IF SHIFT
																									FREQUENCY
																						P1		40	DIRECTION
	cut-off frequency.																								IF SHIFT
		ReadSet			1	2		3		4		5	6	7	8	9	10	11	12	13	14	Note:
Input					I		S	P1				P2			;							If P2 is positive or zero, P1 can be “+” or “ ”.
																						Allowable data (in units of Hz):
					1	2		3		4		5	6	7	8	9	10	11	12	13	14	SSB:	1400, 1600, 1800, 2000, 2200,
					I	S		;														2400, 2600, 2800, 3000, 3400, 4600, 6000
																						AM:	2500, 3000, 4000, 5000, 6000,
Output		Answer			1	2		3		4		5	6	7	8	9	10	11	12	13	14		7000,
					I		S	P1				P2			;							CW:	400~1000 (50 Hz steps)
KS				KEYER SPEED
																						Parameter		Format	Parameter function
Function	Sets or reads keying speed while using the KY command.																					P1		42	KEYER SPEED
			Set		1	2		3		4		5	6	7	8	9	10	11	12	13	14
Input					K		S				P1		;
			Read		1	2		3		4		5	6	7	8	9	10	11	12	13	14
					K		S	;
Output			Answer		1	2		3		4		5	6	7	8	9	10	11	12	13	14
					K		S				P1		;
KY				CW KEYING
																						Parameter		Format	Parameter function
Function	Converts input characters into Morse code.																					P1		43	KEYER MESSAGE
																						P2		44	KEYER BUFFER
																						Note:
					1	2		3		4		5	6	7	8	9	10	11	12	13	14
				command																		The Set command requires a " " (ASCII
commands		Set			K		Y									P1
																						code 20h) in the third byte position.
					15	16		17		18		19	20	21	22	23	24	25	26	27	28	Insert "	" for bytes that have no
																					;	characters to make a 28-byte fixed length
																						command.
					1	2		3		4		5	6	7	8	9	10	11	12	13	14
Input				command																		The "	" bytes will not send any character.
		Read			K		Y	;														Supported characters include: Letters,
					15	16		17		18		19	20	21	22	23	24	25	26	27	28	numbers, " ' (( )) ( )			+ ,– . / : = ?
																						The internal buffer allows approximately
																						5 times 28 characters (~140 characters) to be
					1	2		3		4		5	6	7	8	9	10	11	12	13	14
commandsOutput			commandAnswer																			continuously keyed. For programs that
					K		Y		P2	;												convert to Morse code immediately after entry,
					15	16		17		18		19	20	21	22	23	24	25	26	27	28	more continuous keying is possible
																						Ex:
																						CQ CQ CQ DE WD6DJY WD6DJY WD6DJY K
					29	30		31		32		33	34	35	36	37	38	39	40	41	42
																						KY_CQ_CQ_ CQ_DE_ WD6DJY_ WD6DJ;
																						KY_Y_ WD6DJY_K_______________ ;

91