Kenwood TS-870S instruction manual Not Used

●APPENDICES

LK			LOCK
																			Parameter	Format	Parameter function
Function	Sets Lock OFF/ON or reads status.																		P1	1	LOCK OFF/ON
		Set		1		2	3	4	5	6	7	8	9	10	11	12	13	14
Input					L	K	P1	;
		Read		1		2	3	4	5	6	7	8	9	10	11	12	13	14
					L	K	;
Output		Answer		1		2	3	4	5	6	7	8	9	10	11	12	13	14
					L	K	P1	;

ML			TRANSMIT MONITOR LEVEL
																			Parameter	Format	Parameter function
Function	Sets or reads transmit monitor level.																		P1	46	TRANSMIT
																					MONITOR
																					LEVEL
		Set		1		2	3	4	5	6	7	8	9	10	11	12	13	14
Input					M	L		P1		;
		Read		1		2	3	4	5	6	7	8	9	10	11	12	13	14
					M	L	;
Output		Answer		1		2	3	4	5	6	7	8	9	10	11	12	13	14
					M	L		P1		;

LM			LOAD MESSAGE
																			Parameter	Format	Parameter function
Function	DRS recording																		P1	45	LOAD
																					MESSAGE
		Set		1		2	3	4	5	6	7	8	9	10	11	12	13	14
Input					L	M	P1	;
		Read		1		2	3	4	5	6	7	8	9	10	11	12	13	14
					L	M	;
Output		Answer		1		2	3	4	5	6	7	8	9	10	11	12	13	14
					L	M	P1	;

MC			MEMORY CHANNEL
																			Parameter	Format	Parameter function
Function	Sets or reads memory channels.																		P1	_	NOT USED
																			P2	7	MEMORY CHANNEL
		Set		1		2	3	4	5	6	7	8	9	10	11	12	13	14
ut					M	C			P2	;
MD			MODE
																			Parameter	Format	Parameter function
Function	Sets or reads modes.																		P1	2	MODE
		Set		1		2	3	4	5	6	7	8	9	10	11	12	13	14
Input					M	D	P1	;
		Read		1		2	3	4	5	6	7	8	9	10	11	12	13	14
					M	D	;
Output		Answer		1		2	3	4	5	6	7	8	9	10	11	12	13	14
					M	D	P1	;
MG		MIC GAIN
																			Parameter	Format	Parameter function
Function	Sets or reads MIC gain.																		P1	31	MIC GAIN
		Set		1		2	3	4	5	6	7	8	9	10	11	12	13	14
Input					M	G		P1		;
		Read		1		2	3	4	5	6	7	8	9	10	11	12	13	14
					M	G	;
Output		Answer		1		2	3	4	5	6	7	8	9	10	11	12	13	14
					M	G		P1		;

MN				TRANSMIT MONITOR
																					Parameter	Format	Parameter function
Function	Sets Transmit Monitor OFF/ON or reads status.																				P1	1	TRANSMIT
																							MONITOR
																							OFF/ON
		Set			1		2		3	4	5	6	7	8	9	10	11	12	13	14
Input						M		N	P1	;
		Read			1		2		3	4	5	6	7	8	9	10	11	12	13	14
						M		N	;
Output		Answer			1		2		3	4	5	6	7	8	9	10	11	12	13	14
						M		N	P1	;
MR				MEMORY READ
Function																					Parameter	Format	Parameter function
																					P3	7	MEMORY CHANNEL
	Reads memory.																				P1	9	SPLIT DATA
																					P2	–	NOT USED
				command	1		2		3	4	5	6	7	8	9	10	11	12	13	14	P4	4	FREQUENCY
commands		Set			1		2		3	4	5	6	7	8	9	10	11	12	13	14	P9	–	NOT USED
																					P5	2	MODE
					15		16		17	18	19	20	21	22	23	24	25	26	27	28	P6	10	MEMORY LOCKOUT
																					P7	1	TONE OFF/ON
Input				command																	P8	14	TONE NUMBER
		Read				M		R	P1		P3		;								Note:
																					For a vacant channel, the Answer command
					15		16		17	18	19	20	21	22	23	24	25	26	27	28
																					sends "0" for all parameters except the
																					memory channel number.
																					P1 must be "0" to read the CH 99 Start
					1		2		3	4	5	6	7	8	9	10	11	12	13	14
commandsOutput			commandAnswer																		frequency and "1" to read the End frequency.
						M		R	P1		P3					P4
					15		16		17	18	19	20	21	22	23	24	25	26	27	28
										P5	P6	P7	P8			;
					29		30		31	32	33	34	35	36	37	38	39	40	41	42
MW				MEMORY WRITE
																					Parameter	Format	Parameter function
Function																					P3	7	MEMORY CHANNEL
	Writes into memory.																				P1	9	SPLIT DATA
																					P2	–	NOT USED
				command	1		2		3	4	5	6	7	8	9	10	11	12	13	14	P4	4	FREQUENCY
commands		Set			1		2		3	4	5	6	7	8	9	10	11	12	13	14	P9	–	NOT USED
						M		W	P1		P3					P4					P5	2	MODE
					15		16		17	18	19	20	21	22	23	24	25	26	27	28	P6	10	MEMORY LOCKOUT
										P5	P6	P7	P8			;					P7	1	TONE OFF/ON
Input																					P8	14	TONE NUMBER
				command
		Read																			Note:
																					All parameters must be entered.
					15		16		17	18	19	20	21	22	23	24	25	26	27	28
																					The memory channel becomes a vacant
																					channel if all frequency digits are "0".
																					Other parameters are ignored.
					1		2		3	4	5	6	7	8	9	10	11	12	13	14
commandsOutput			commandAnswer																		P1 must be "0" to store a Start frequency
																					and "1" to store an End frequency.
					15		16		17	18	19	20	21	22	23	24	25	26	27	28
					29		30		31	32	33	34	35	36	37	38	39	40	41	42

92