Projector Features, Usage Guidelines | Kodak DP2000 specs

Projector Features

Introduction

Projector Features

speaker

keypad	Hand grip

zoom ring

KENSINGTON

Lock

focus ring	connector panel

power cord connector

Usage Guidelines

•Do not look directly into the projection lens when the lamp is turned on. The bright light may harm your eyes.

•Do not block the grills on the projector. Restricting the air flow can cause it to overheat and turn off. If this happens, you must wait a minute before attempting to turn it back on.

•Handle the projector as you would any product with glass components. Be especially careful not to drop it.

•Avoid leaving the projector in direct sunlight or extreme cold for extended periods of time. If this happens, allow it to reach room temperature before use.

•Transport the projector in a Kodak-approved hard or soft case.

7

Image 13

Kodak DP2000 manual Projector Features, Usage Guidelines

Contents

User’s Guide KODAK DP2000 Digital Projector with KODAK Image Manager SoftwarePage FCC Warning Safety CertificationsCanada EN 55022 WarningPage Safety Instructions Table of ContentsSetting up the Projector Using the Projector Appendix B Appendix AAppendix C Appendix D Safety Definitions Safety InstructionsSafety Symbols Important Operating Considerations Safety Terms Battery Use Page Introduction Image ResolutionCompatibility User’s Guide , Quick Start Guide Unpacking the Projectorand Online User Guide CD Usage Guidelines Projector Features If You Need Assistance Online ServicesFaxed Information Customer Support Warranty Positioning the Projector Setting up the Projector Connecting to a Computer Connecting the Projector Do you want to play your computer’s audio on the projector? To connect to a computer If your computer has a PS/2 connector, use the PS/2 mouse cable To connect to a video player Connecting to a Video Player 4. Plug the other end of the audio adapter into the audio cable Starting the Projector Turning Off the Projector Basic Image Adjustment Using the Projector Adjusting the Projector Using the Projector The Remote Controldisk mouse simulates the right mouse button simulates the left mouse button Press anywhere on the edge of the disk mouse to move the cursor on the screen. You can move the cursor at any angle by pressing the corresponding edge of the disk. The mouse button on the top of the remote simulates your computer’s right mouse button the button on the bottom simulates your computer’s left mouse button. See “Using the Keypad and Remote Control” starting on page 23 for a description of the four function buttons The Remote Control Buttons Using the Keypad and Remote ControlThe Keypad Buttons Lamp on/off keypad only Volume keypad onlyMenu or Computer and Video KHQWKHPHQXRSWLRQLVDFWLYH XVHWKHVHEXWWRQVWRQDYLJDWH WKURXJKWKHPHQXV Using the On-Screen Menus Brightness Display MenuContrast Reset All Audio MenuVolume Tint Auto Image Image MenuAuto Resize Manual Tracking Manual SyncHorizontal position Vertical position Controls MenuVideo Standard Standby Time Default SourceRear Projection Auto Source Select Display Messages Plug and PlayDisplay Startup Screen Status Menu Language Menu Lamp hours used Computer resolutionHorizontal refresh rate Vertical refresh rate Image Manager Settings Kodak Menu The new contrast setting is immediately applied to the image Using the Image Manager1. Click the Kodak menu Cleaning the Lens Maintenance Troubleshooting SURMHFWRUWRRYHUKHDW Replacing the Projection Lamp Maintenance & Troubleshooting Be careful when removing the lamp module so that it does not break5. Loosen the two non-removable screws on the outside of the module 6. Grasp the pull tab and lift out the lamp module 3OXJLQWKHSRZHUFRUGWRWXUQWKHSURMHFWRUEDFNRQ 9. Tighten the screws on the outside of the module5HSODFHWKHODPSGRRUE\LQVHUWLQJWKHKRRNVRQWKHUHDURIWKH 7RUHVHWWKHODPSKRXUFRXQWHULQWKH6WDWXVZLQGRZSUHVVDQG Using the Kensington Lock Replacing the Batteries in the Remote Control Problem Nothing on projection screen TroubleshootingProblem Color or text not being projected Problem The screen resolution is not right Problem Image is too wide or narrow for screen Problem Only the start-up screen displaysProblem Image is out of focus Problem the projector displays vertical lines, “bleeding” or spots Problem Image and menus are reversed left to rightProblem no sound Problem Image is “noisy” or streaked Problem Lamp shuts off Problem Lamp seems to be getting dimmerPage Dimensions SpecificationsWeight Appendix A Optics Input Power RequirementsLamp Audio Input Key command Portable and Laptop Activation ChartAppendix B Computer Key command Key commandComputer de-activate Key command Key commandComputer de-activate Key command Key commandComputer de-activate Key command Key commandComputer de-activate Key command Key commandComputer de-activate Key command Key commandComputer de-activate Key command Key commandComputer de-activate Key command Key commandComputer de-activatePage Appendix C Using Video Mirroring with a PowerBook Computer Using SimulScan Projected Image Size Appendix D Image Size, Width and Height for DP2000-minimum image size Image Size, Width and Height for DP2000-maximum image size Index L lamp H helpPage Page WARRANTY REPAIR COVERAGE WARRANTY TIME PERIODLIMITATIONS APPLICATION SUPPORT HOW TO OBTAIN SERVICE Page Kodak is a trademark of Eastman Kodak Company Eastman Kodak Company 343 State Street Rochester, New YorkPN 3H7969 9/99