Problem Image and menus are reversed left to right | Kodak DP2000

Problem: Image and menus are reversed left to right

User’s Guide KODAK DP2000 Digital Projector

Problem: Image and menus are reversed left to right

•Rear projection mode is probably turned on. Turn Rear Projection off in the Controls menu. The image should immediately return to forward projection. See “Rear Projection” on page 31.

Problem: the projector displays vertical lines, “bleeding” or spots

•Adjust the brightness. See “Brightness” on page 26.

•Check the projection lens to see if it needs cleaning.

Problem: no sound

•Adjust the volume.

•Verify the audio/input connections.

•Adjust the audio source.

Problem: Image is “noisy” or streaked

Try these steps in this order.

1.Deactivate the screen saver on your computer.

2.Turn Auto Image off and then back on again. See “Auto Image” on page 28.

3.Turn Auto Image off and adjust the synchronization and tracking manually to find an optimal setting. See “Manual Sync” on page 29 and “Manual Tracking” on page 29.

•The problem could be with your computer’s video card. If possible, connect a different computer.

44

Image 50

Kodak DP2000 Problem Image and menus are reversed left to right, Problem no sound, Problem Image is “noisy” or streaked

Contents

with KODAK Image Manager Software User’s Guide KODAK DP2000 Digital ProjectorPage Canada Safety CertificationsFCC Warning EN 55022 WarningPage Setting up the Projector Table of ContentsSafety Instructions Using the Projector Appendix C Appendix AAppendix B Appendix D Safety Symbols Safety InstructionsSafety Definitions Safety Terms Important Operating Considerations Battery Use Page Compatibility Image ResolutionIntroduction and Online User Guide CD Unpacking the ProjectorUser’s Guide , Quick Start Guide Projector Features Usage Guidelines Faxed Information Online ServicesIf You Need Assistance Customer Support Warranty Setting up the Projector Positioning the Projector Connecting the Projector Connecting to a Computer To connect to a computer Do you want to play your computer’s audio on the projector? If your computer has a PS/2 connector, use the PS/2 mouse cable Connecting to a Video Player To connect to a video player 4. Plug the other end of the audio adapter into the audio cable Starting the Projector Turning Off the Projector Using the Projector Basic Image Adjustment Adjusting the Projector disk mouse simulates the right mouse button The Remote ControlUsing the Projector simulates the left mouse button Press anywhere on the edge of the disk mouse to move the cursor on the screen. You can move the cursor at any angle by pressing the corresponding edge of the disk. The mouse button on the top of the remote simulates your computer’s right mouse button the button on the bottom simulates your computer’s left mouse button. See “Using the Keypad and Remote Control” starting on page 23 for a description of the four function buttons The Keypad Buttons Using the Keypad and Remote ControlThe Remote Control Buttons Menu Volume keypad onlyLamp on/off keypad only or Computer and Video Using the On-Screen Menus KHQWKHPHQXRSWLRQLVDFWLYH XVHWKHVHEXWWRQVWRQDYLJDWH WKURXJKWKHPHQXV Contrast Display MenuBrightness Volume Audio MenuReset All Tint Auto Resize Image MenuAuto Image Horizontal position Manual SyncManual Tracking Video Standard Controls MenuVertical position Rear Projection Default SourceStandby Time Auto Source Select Display Startup Screen Plug and PlayDisplay Messages Language Menu Status Menu Horizontal refresh rate Computer resolutionLamp hours used Vertical refresh rate Kodak Menu Image Manager Settings 1. Click the Kodak menu Using the Image ManagerThe new contrast setting is immediately applied to the image Maintenance Troubleshooting Cleaning the Lens Replacing the Projection Lamp SURMHFWRUWRRYHUKHDW 5. Loosen the two non-removable screws on the outside of the module Be careful when removing the lamp module so that it does not breakMaintenance & Troubleshooting 6. Grasp the pull tab and lift out the lamp module 5HSODFHWKHODPSGRRUE\LQVHUWLQJWKHKRRNVRQWKHUHDURIWKH 9. Tighten the screws on the outside of the module3OXJLQWKHSRZHUFRUGWRWXUQWKHSURMHFWRUEDFNRQ 7RUHVHWWKHODPSKRXUFRXQWHULQWKH6WDWXVZLQGRZSUHVVDQG Replacing the Batteries in the Remote Control Using the Kensington Lock Problem Color or text not being projected TroubleshootingProblem Nothing on projection screen Problem The screen resolution is not right Problem Image is out of focus Problem Only the start-up screen displaysProblem Image is too wide or narrow for screen Problem no sound Problem Image and menus are reversed left to rightProblem the projector displays vertical lines, “bleeding” or spots Problem Image is “noisy” or streaked Problem Lamp seems to be getting dimmer Problem Lamp shuts offPage Weight SpecificationsDimensions Appendix A Lamp Input Power RequirementsOptics Audio Input Appendix B Portable and Laptop Activation ChartKey command Computer Computer Key commandKey command de-activate Computer Key commandKey command de-activate Computer Key commandKey command de-activate Computer Key commandKey command de-activate Computer Key commandKey command de-activate Computer Key commandKey command de-activate Computer Key commandKey command de-activate Computer Key commandKey command de-activatePage Using Video Mirroring with a PowerBook Computer Appendix C Using SimulScan Appendix D Projected Image Size Image Size, Width and Height for DP2000-maximum image size Image Size, Width and Height for DP2000-minimum image size Index H help L lampPage Page LIMITATIONS WARRANTY TIME PERIODWARRANTY REPAIR COVERAGE APPLICATION SUPPORT HOW TO OBTAIN SERVICE Page PN 3H7969 Eastman Kodak Company 343 State Street Rochester, New YorkKodak is a trademark of Eastman Kodak Company 9/99