Controls Menu, Vertical position, Video Standard | Kodak DP2000

Vertical position

User’s Guide KODAK DP2000 Digital Projector

Vertical position

Note: The Vert. Position option is available only for computer sources. The projector sets this option automatically for a video source.

Follow these steps to manually adjust the vertical position.

1.Turn Auto Image off.

2.Highlight Vertical position, then press the left navigation button to move the image down or press the right navigation button to move the image up.

Positioning adjustments are saved when you power off the projector.

Controls Menu

Video Standard

When Video standard is set to Auto, the projector attempts to pick the video standard (NTSC, NTSC 4.43, PAL, PAL-M, PAL-N, or SECAM) automatically based on the input signal it receives. (The video standard options may vary depending on your region of the world.) If the projector is unable to detect the correct standard, the colors might not look right or the image might appear “torn.” If this happens, manually select a standard by clicking either the left or right navigation button and cycling through the standards.

Note: If you already know the video standard used in your geographical area, it’s best to manually select it.

30

Image 36

Kodak DP2000 manual Controls Menu, Vertical position, Video Standard

Contents

with KODAK Image Manager Software User’s Guide KODAK DP2000 Digital ProjectorPage Safety Certifications FCC WarningCanada EN 55022 WarningPage Table of Contents Safety InstructionsSetting up the Projector Using the Projector Appendix A Appendix BAppendix C Appendix D Safety Instructions Safety DefinitionsSafety Symbols Safety Terms Important Operating Considerations Battery Use Page Image Resolution IntroductionCompatibility Unpacking the Projector User’s Guide , Quick Start Guideand Online User Guide CD Projector Features Usage Guidelines Online Services If You Need AssistanceFaxed Information Customer Support Warranty Setting up the Projector Positioning the Projector Connecting the Projector Connecting to a Computer To connect to a computer Do you want to play your computer’s audio on the projector? If your computer has a PS/2 connector, use the PS/2 mouse cable Connecting to a Video Player To connect to a video player 4. Plug the other end of the audio adapter into the audio cable Starting the Projector Turning Off the Projector Using the Projector Basic Image Adjustment Adjusting the Projector The Remote Control Using the Projectordisk mouse simulates the right mouse button simulates the left mouse button Press anywhere on the edge of the disk mouse to move the cursor on the screen. You can move the cursor at any angle by pressing the corresponding edge of the disk. The mouse button on the top of the remote simulates your computer’s right mouse button the button on the bottom simulates your computer’s left mouse button. See “Using the Keypad and Remote Control” starting on page 23 for a description of the four function buttons Using the Keypad and Remote Control The Remote Control ButtonsThe Keypad Buttons Volume keypad only Lamp on/off keypad onlyMenu or Computer and Video Using the On-Screen Menus KHQWKHPHQXRSWLRQLVDFWLYH XVHWKHVHEXWWRQVWRQDYLJDWH WKURXJKWKHPHQXV Display Menu BrightnessContrast Audio Menu Reset AllVolume Tint Image Menu Auto ImageAuto Resize Manual Sync Manual TrackingHorizontal position Controls Menu Vertical positionVideo Standard Default Source Standby TimeRear Projection Auto Source Select Plug and Play Display MessagesDisplay Startup Screen Language Menu Status Menu Computer resolution Lamp hours usedHorizontal refresh rate Vertical refresh rate Kodak Menu Image Manager Settings Using the Image Manager The new contrast setting is immediately applied to the image1. Click the Kodak menu Maintenance Troubleshooting Cleaning the Lens Replacing the Projection Lamp SURMHFWRUWRRYHUKHDW Be careful when removing the lamp module so that it does not break Maintenance & Troubleshooting5. Loosen the two non-removable screws on the outside of the module 6. Grasp the pull tab and lift out the lamp module 9. Tighten the screws on the outside of the module 3OXJLQWKHSRZHUFRUGWRWXUQWKHSURMHFWRUEDFNRQ5HSODFHWKHODPSGRRUE\LQVHUWLQJWKHKRRNVRQWKHUHDURIWKH 7RUHVHWWKHODPSKRXUFRXQWHULQWKH6WDWXVZLQGRZSUHVVDQG Replacing the Batteries in the Remote Control Using the Kensington Lock Troubleshooting Problem Nothing on projection screenProblem Color or text not being projected Problem The screen resolution is not right Problem Only the start-up screen displays Problem Image is too wide or narrow for screenProblem Image is out of focus Problem Image and menus are reversed left to right Problem the projector displays vertical lines, “bleeding” or spotsProblem no sound Problem Image is “noisy” or streaked Problem Lamp seems to be getting dimmer Problem Lamp shuts offPage Specifications DimensionsWeight Appendix A Input Power Requirements OpticsLamp Audio Input Portable and Laptop Activation Chart Key commandAppendix B Computer Key command Key commandComputer de-activate Key command Key commandComputer de-activate Key command Key commandComputer de-activate Key command Key commandComputer de-activate Key command Key commandComputer de-activate Key command Key commandComputer de-activate Key command Key commandComputer de-activate Key command Key commandComputer de-activatePage Using Video Mirroring with a PowerBook Computer Appendix C Using SimulScan Appendix D Projected Image Size Image Size, Width and Height for DP2000-maximum image size Image Size, Width and Height for DP2000-minimum image size Index H help L lampPage Page WARRANTY TIME PERIOD WARRANTY REPAIR COVERAGELIMITATIONS APPLICATION SUPPORT HOW TO OBTAIN SERVICE Page Eastman Kodak Company 343 State Street Rochester, New York Kodak is a trademark of Eastman Kodak CompanyPN 3H7969 9/99