18
Sequencer mode

SEQ 5.3: Tone Adjust

System version 2.0 adds a SEQ 5.3: Tone Adjust pagefollowing the 5.3: Track Edit page (☞PG p.102) of Se-quencer mode.
5.3–1: TA1..8 (Tone Adjust1 T01–08)
5.3–2: TA1..16 (Tone Adjust1 T09–16)
5.3–3: TA2..8 (Tone Adjust2 T01–08)
5.3–4: TA2..16 (Tone Adjust2 T09–16)
5.3–5: TA3..8 (Tone Adjust3 T01–08)
5.3–6: TA3..16 (Tone Adjust3 T09–16)
These pages let you make temporary adjustments to thesound of the program used by each track. While you arecreating a song, you can make adjustments such as makingthe bass more mellow or giving the strings a sharper attackwithout having to go back to Program mode and edit theprograms. For each track in a song, you can select andadjust up to six parameters such as filter cutoff, resonance,filter EQ, and amp EG.
5.3–1a
5.3–1b
5.3–1(2)(3)(4)(5)(6)a: Destination 1–6, Value 1–6
Destination 1–6 [LPF Fc…Reverse]
Selects the parameter that you want to adjust.
Value 1–6
[-99…+99, -12.00…+12.00, -1200…+1200, Off…On]
Specifies the value for the parameter you selected in“Destination 1–6.” If you set this to +00 or PRG, the settingof the program will be used.
Normally, you should not select the same parameter
for more than one “Destination” in the same track.
However if you do so, the parameters will operate as
follows.
If you select other than Hold or Reverse
The “Value” of each “Destination” set to the same
parameter will be summed for each track. However,
the “Value” of the parameter being controlled by the
“Destination” will not exceed the allowable range of
settings. For example if you have assigned three
Detune1 settings for the same track, and their “Value”
settings are set to +1000, +1000, and +1000 respectively,
then the result will be +1200. (The sum is +3000, but
the value is limited at the maximum of +1200 for the
Detune1 parameter.) Settings of +1000, +1000, and -
1000 would produce a result of +1000.
Hold, Reverse
The last of the multiple “Destination” settings will be
valid.
“Destination 1–6” and “Value 1–6”
The parameters that can be controlled and their range of
values are as follows.
LPF Fc (Low Pass Filter Cutoff Frequency) [-99…+00…+99]
Adjusts the low pass filter cutoff frequency of program
OSC 1/2. This will affect the brightness of the sound. The
parameter will be controlled in the same way as when
CC#74 is received. (☞PG p.243, Bank F: p.273)
Reso.HP (Resonance/High Pass Filter Cutoff Frequency)[-99…+00…+99]
Adjusts the resonance level of the low pass filter or the
cutoff frequency of the high pass filter for program OSC 1/
2. The parameter that is controlled will depend on the filter
type specified for the program. The parameter will be
controlled in the same way as when CC#71 is received.
(☞PG p.243, Bank F: p.273)
F EG Int (Filter EG Intensity) [-99…+00…+99]
Adjusts the filter EG intensity (the depth of the filter EG)
for program OSC1/2. The parameter will be controlled in
the same way as when CC#79 is received. (☞PG p.244,
Bank F: p.274)
A Vel I. (Amp Velocity Intensity) [-99…+00…+99]
Adjusts the amp velocity intensity (the degree to which
velocity will affect the amp) for program OSC 1/2. This
controls the Amp Modulation “Velocity Intensity” param-
eter (5.1-2b ☞PG p.21).
For bank F programs, this controls the Amp EG Level
Modulation “Velocity Control” parameter (☞PG
p.285).
F.A EG A (Filter/Amp EG Attack Time) [-99…+00…+99]
Adjusts the EG attack times of the program OSC 1/2 filter
and amp. To maximize the result of this adjustment, the
Amp EG sustain level, attack level, start level modulation,
and attack time modulation will also be adjusted at the
same time. The parameter will be controlled in the same
way as when CC#73 is received. (☞PG p.243, Bank F: p.273)
F.A EG D (Filter/Amp EG Decay Time) [-99…+00…+99]
Adjusts the EG decay time and slope time of the program
OSC 1/2 filter and amp. The parameter will be controlled
in the same way as when CC#75 is received. (☞PG p.243,
Bank F: p.273)
F.A EG S (Filter/Amp EG Sustain Level) [-99…+00…+99]
Adjusts the EG sustain level of the program OSC 1/2 filter
and amp. The parameter will be controlled in the same way
as when CC#70 is received. (☞PG p.243, Bank F: p.273)
F.A EG R (Filter/Amp EG Release Time) [-99…+00…+99]
Adjusts the EG release time of the program OSC 1/2 filter
and amp. The parameter will be controlled in the same way
as when CC#72 is received. (☞PG p.243, Bank F: p.273)
F EG A (Filter EG Attack Time) [-99…+00…+99]F EG D (Filter EG Decay Time) [-99…+00…+99]F EG S (Filter EG Sustain Level) [-99…+00…+99]F EG R (Filter EG Release Time) [-99…+00…+99]
These adjust only the filter parameter as in “F.A EG A,”
“F.A EG D,” “F.A EG S,” or “F.A EG R” respectively.