Slots in the printer | Kyocera FS-1010 guide

Cleaning

If the charger cleaner knob is not restored to its home position (marked CLEANER HOME POSITION ), a black band will print along the length of the page the next time you use the printer.

5	After cleaning is done, put the process unit back in the printer. To do
	so, carefully align the guides at both ends of the process unit with

the slots in the printer.

Process Unit

6	Close the front cover.

Front Cover

7	Close the top cover by pressing down on the front left and right
	corners of the top cover.

Top Cover

2-8

Image 24

Kyocera FS-1010 manual Slots in the printer

Contents

Printer Regarding Tradenames Limited Warranty LicenseLimitation of Remedies General Typeface Trademark Acknowledgement Agfa Japan License Agreement Guidelines Contents Paper Selection FontsAppendix a Options Appendix B Host Computer Interface Appendix C Printer Specifications Glossary-1Index-1 Introduction Guide to the Manuals Description Guide to the Operation Guide Basic Operations Operator Panel Indicators KeysReference Name Status Meaning Reference Name Function Status Installation Options Error LogSoftware Version Hardware Information Toner Gauge Interface InformationKIR Test Pattern Maintenance Toner Container Replacement Toner Container Replacement IntervalToner Kit to be Used Replenishing Toner Take the new toner container from the bag. Hold it with Lock Lock position. Lock lever #2 is automatically locked Cleaning Printer Interior Never stand the process unit on end Slots in the printer Troubleshooting Symptom Check Items Corrective Action General Guide Print Quality Problems Clean the charger wirePrinted Results Corrective Action Contact your Kyocera Mita dealer Check the EcoPrint setting Confirm Toner indicatorTry setting the thin paper mode Check the paper size setting Indicators Maintenance Messages Theprintjobcannotbedoneatcurrentresolution There is no cassette in the feeder, orCassette is not inserted properly After reinserting the paper cassette, you should be Errors Requiring Service Personnel Attention Scanner motor error 4000 errorScanner pin-photo error 4200 error Eraser error 5300 error Error None Waste toner reservoir is full ErrorController RAM read/write error F020 error Waste toner reservoir is full Communication error F040 error Engine ROM check sum error F050 error Error Messages Printer power is on Make sure to turn the printer power off before insertingThis message appears when the printer is in the ready Printer has halted because you attempted to insert Normal Indicator Display Indicator KM-NET for Clients display Description Correcting a Paper Jam Jam at the Face-down and Face-up Trays Jam at the Paper Cassette Jam Inside the Printer Into the printer Paper Selection Paper Specifications SpecificationsSpecification General Guidelines Selecting the Right Paper Condition of the PaperComposition Basis Weight Paper SizePaper Sizes for Paper Feeding Smoothness Moisture Content Thickness CaliperPaper Grain Other Paper Properties Transparency Specifications Special PaperTransparency overhead projection film Adhesive-Backed Labels Adhesive-backed label Adhesive Label Specifications EnvelopesColored Paper Preprinted Paper Recycled Paper Paper Source MP Tray Paper Weight Paper Type Cassette Paper TypePaper Type Fonts Internal Fonts List of Fonts Internal Scalable and Bitmap Fonts and Kpdl Fonts List of Fonts List of Fonts Font Kpdl Fonts List of Fonts Appendix a Options Available Options Memory CompactFlash Card Expansion Memory Installation YES Installing the Dimm Dimm to be used Insert the Dimm into the Dimm socket so that the notches on Testing the Expansion Memory To remove a Dimm Setting the Printer Driver Memory CompactFlash Card Push it in all the way Network Interface Card Appendix B Host Computer Interface Interface Signals Parallel InterfaceParallel Interface Communication Modes Table B.1 Parallel Connector Pin Assignment Pin In/out Description Data 0 1 to Data 7 8 Pins 2 to Paper Empty PError PinReset nInit Pin Error* nFault Pin Power Ready Pin Select In nSelectIn Pin Specifications USB Interface Serial Interface Option 1 RS-232C Interface SG Signal Ground Pin Table B.4 RS-422A Signal Pin Assignments2 RS-422A Interface DTR Data Terminal Ready Pin Overview of Signals RS-422A Serial ConnectorRDB Receive Data Pin RDA Receive Data Inverted Pin SDB Send Data Pin SDA Send Data Inverted Pin RS-232C/RS-422A Protocol H1 Baud rateH2 Data bits H3 Stop bits Prescribe Frpo D0 Command H5 Protocol logicH6 Buffer nearly-full threshold H7 Buffer nearly-empty threshold Connecting the Printer to the Computer RS-232C Cable ConnectionObtain a Suitable RS-232C Cable Cursor with Settings, then click on Control Panel from among \MODE LPT1=COM1 Appendix C Printer Specifications Printer Specifications Power requirements Power consumptionDimensions Weight Glossary Cassette mode First modeDpi dots per inch IEEE1284 Prescribe commands MB mega byteMP tray Offline Sleep mode StatusUSB Universal Serial Bus Index EcoPrint Glossary-2Emulation Glossary-2Envelope Index-3