RS-232C/RS-422A Protocol, H1 Baud rate, H4 Parity | Kyocera FS-1010

RS-232C/RS-422A Protocol

B.4 RS-232C/RS-422A Protocol

A protocol is a set of rules the computer follows in sending data to the printer. The RS-232C/RS-422A parameters are stored in battery backed-up memory. They are indicated on the status printout. They can be changed by the FRPO (firmware reprogram) command described in the Programming Manual provided on the CD-ROM supplied with the printer. The parameters and their identification codes are given below.

H1: Baud rate

Parameter value		Baud rate
12		1200

24		2400

48		4800

96		9600

19		19200

38		38400

57		57600

11		115200

The factory setting is 9600 baud.
H2: Data bits
7 or 8, factory-set to 8.
H3: Stop bits
1 or 2, factory-set to 1.
H4: Parity

Parameter value		Meaning
0		None

1		Odd

2		Even

3		Ignore

The factory setting is “None” (0 on the status printout).

B-10

Image 78

Kyocera FS-1010 manual RS-232C/RS-422A Protocol, H1 Baud rate, H2 Data bits, H3 Stop bits, H4 Parity

Contents

Printer Regarding Tradenames Limitation of Remedies Limited WarrantyLicense General Typeface Trademark Acknowledgement Agfa Japan License Agreement Guidelines Contents Appendix a Options Paper SelectionFonts Appendix B Host Computer Interface Appendix C Printer Specifications Glossary-1Index-1 Introduction Guide to the Manuals Description Guide to the Operation Guide Basic Operations Operator Panel Reference Name Status Meaning IndicatorsKeys Reference Name Function Status Software Version Installation OptionsError Log Hardware Information Toner Gauge Interface InformationKIR Test Pattern Maintenance Toner Container Replacement Toner Container Replacement IntervalToner Kit to be Used Replenishing Toner Take the new toner container from the bag. Hold it with Lock Lock position. Lock lever #2 is automatically locked Cleaning Printer Interior Never stand the process unit on end Slots in the printer Troubleshooting Symptom Check Items Corrective Action General Guide Printed Results Corrective Action Print Quality ProblemsClean the charger wire Contact your Kyocera Mita dealer Try setting the thin paper mode Check the EcoPrint settingConfirm Toner indicator Check the paper size setting Indicators Maintenance Messages Cassette is not inserted properly TheprintjobcannotbedoneatcurrentresolutionThere is no cassette in the feeder, or After reinserting the paper cassette, you should be Scanner pin-photo error 4200 error Errors Requiring Service Personnel AttentionScanner motor error 4000 error Eraser error 5300 error Controller RAM read/write error F020 error ErrorNone Waste toner reservoir is full Error Waste toner reservoir is full Communication error F040 error Engine ROM check sum error F050 error Error Messages This message appears when the printer is in the ready Printer power is onMake sure to turn the printer power off before inserting Printer has halted because you attempted to insert Normal Indicator Display Indicator KM-NET for Clients display Description Correcting a Paper Jam Jam at the Face-down and Face-up Trays Jam at the Paper Cassette Jam Inside the Printer Into the printer Paper Selection Specification Paper SpecificationsSpecifications General Guidelines Selecting the Right Paper Condition of the PaperComposition Paper Sizes for Paper Feeding Basis WeightPaper Size Smoothness Moisture Content Thickness CaliperPaper Grain Other Paper Properties Transparency Specifications Special PaperTransparency overhead projection film Adhesive-Backed Labels Adhesive-backed label Colored Paper Adhesive Label SpecificationsEnvelopes Preprinted Paper Recycled Paper Paper Source MP Tray Paper Weight Paper Type Cassette Paper TypePaper Type Fonts Internal Fonts List of Fonts Internal Scalable and Bitmap Fonts and Kpdl Fonts List of Fonts List of Fonts Font Kpdl Fonts List of Fonts Appendix a Options Available Options Memory CompactFlash Card Expansion Memory Installation YES Installing the Dimm Dimm to be used Insert the Dimm into the Dimm socket so that the notches on Testing the Expansion Memory To remove a Dimm Setting the Printer Driver Memory CompactFlash Card Push it in all the way Network Interface Card Appendix B Host Computer Interface Interface Signals Parallel InterfaceParallel Interface Communication Modes Table B.1 Parallel Connector Pin Assignment Pin In/out Description Reset nInit Pin Data 0 1 to Data 7 8 Pins 2 toPaper Empty PError Pin Error* nFault Pin Power Ready Pin Select In nSelectIn Pin Specifications USB Interface Serial Interface Option 1 RS-232C Interface 2 RS-422A Interface SG Signal Ground PinTable B.4 RS-422A Signal Pin Assignments DTR Data Terminal Ready Pin RDB Receive Data Pin RDA Receive Data Inverted Pin Overview of Signals RS-422ASerial Connector SDB Send Data Pin SDA Send Data Inverted Pin H2 Data bits RS-232C/RS-422A ProtocolH1 Baud rate H3 Stop bits H6 Buffer nearly-full threshold Prescribe Frpo D0 CommandH5 Protocol logic H7 Buffer nearly-empty threshold Connecting the Printer to the Computer RS-232C Cable ConnectionObtain a Suitable RS-232C Cable Cursor with Settings, then click on Control Panel from among \MODE LPT1=COM1 Appendix C Printer Specifications Printer Specifications Dimensions Power requirementsPower consumption Weight Glossary Dpi dots per inch Cassette modeFirst mode IEEE1284 MP tray Prescribe commandsMB mega byte Offline Sleep mode StatusUSB Universal Serial Bus Index EcoPrint Glossary-2Emulation Glossary-2Envelope Index-3