Setting the Printer Driver | Kyocera FS-1010 manual

Expansion Memory Installation

Setting the Printer Driver

After you install the additional memory to the printer, follow the instructions below to set the printer driver so that the printer can use the memories efficiently.

1

2

Click the Windows Start button, point to Settings then click Printers.

Right click the Kyocera Mita FS-1010 KX icon, and click Properties.

The Properties dialog box will open. Click the Device Settings tab.

3	Enter the total memory size installed to the printer (up to 144 MB)
	in the Memory box.

A-7

Image 65

Kyocera FS-1010 manual Setting the Printer Driver

Contents

Printer Regarding Tradenames License Limited WarrantyLimitation of Remedies General Agfa Japan License Agreement Guidelines Typeface Trademark Acknowledgement Contents Fonts Paper SelectionAppendix a Options Appendix B Host Computer Interface Index-1 Appendix C Printer SpecificationsGlossary-1 Introduction Description Guide to the Manuals Guide to the Operation Guide Basic Operations Operator Panel Keys IndicatorsReference Name Status Meaning Reference Name Function Status Error Log Installation OptionsSoftware Version Hardware Information KIR Test Pattern Toner GaugeInterface Information Maintenance Toner Kit to be Used Toner Container ReplacementToner Container Replacement Interval Replenishing Toner Take the new toner container from the bag. Hold it with Lock Lock position. Lock lever #2 is automatically locked Printer Interior Cleaning Never stand the process unit on end Slots in the printer Troubleshooting General Guide Symptom Check Items Corrective Action Clean the charger wire Print Quality ProblemsPrinted Results Corrective Action Contact your Kyocera Mita dealer Confirm Toner indicator Check the EcoPrint settingTry setting the thin paper mode Check the paper size setting Indicators Maintenance Messages There is no cassette in the feeder, or TheprintjobcannotbedoneatcurrentresolutionCassette is not inserted properly After reinserting the paper cassette, you should be Scanner motor error 4000 error Errors Requiring Service Personnel AttentionScanner pin-photo error 4200 error Eraser error 5300 error None Waste toner reservoir is full Error ErrorController RAM read/write error F020 error Waste toner reservoir is full Engine ROM check sum error F050 error Communication error F040 error Error Messages Make sure to turn the printer power off before inserting Printer power is onThis message appears when the printer is in the ready Printer has halted because you attempted to insert Indicator KM-NET for Clients display Description Normal Indicator Display Jam at the Face-down and Face-up Trays Correcting a Paper Jam Jam Inside the Printer Jam at the Paper Cassette Into the printer Paper Selection Specifications Paper SpecificationsSpecification General Guidelines Composition Selecting the Right PaperCondition of the Paper Paper Size Basis WeightPaper Sizes for Paper Feeding Smoothness Paper Grain Moisture ContentThickness Caliper Other Paper Properties Transparency overhead projection film Transparency SpecificationsSpecial Paper Adhesive-backed label Adhesive-Backed Labels Envelopes Adhesive Label SpecificationsColored Paper Preprinted Paper Recycled Paper Paper Type Paper Source MP Tray Paper Weight Paper Type CassettePaper Type Fonts Internal Fonts Internal Scalable and Bitmap Fonts and Kpdl Fonts List of Fonts List of Fonts List of Fonts Font Kpdl Fonts List of Fonts Appendix a Options Memory CompactFlash Card Available Options YES Expansion Memory Installation Dimm to be used Installing the Dimm Insert the Dimm into the Dimm socket so that the notches on To remove a Dimm Testing the Expansion Memory Setting the Printer Driver Memory CompactFlash Card Push it in all the way Network Interface Card Appendix B Host Computer Interface Parallel Interface Communication Modes Interface SignalsParallel Interface Pin In/out Description Table B.1 Parallel Connector Pin Assignment Paper Empty PError Pin Data 0 1 to Data 7 8 Pins 2 toReset nInit Pin Error* nFault Pin Select In nSelectIn Pin Power Ready Pin USB Interface Specifications 1 RS-232C Interface Serial Interface Option Table B.4 RS-422A Signal Pin Assignments SG Signal Ground Pin2 RS-422A Interface DTR Data Terminal Ready Pin Serial Connector Overview of Signals RS-422ARDB Receive Data Pin RDA Receive Data Inverted Pin SDB Send Data Pin SDA Send Data Inverted Pin H1 Baud rate RS-232C/RS-422A ProtocolH2 Data bits H3 Stop bits H5 Protocol logic Prescribe Frpo D0 CommandH6 Buffer nearly-full threshold H7 Buffer nearly-empty threshold Obtain a Suitable RS-232C Cable Connecting the Printer to the ComputerRS-232C Cable Connection Cursor with Settings, then click on Control Panel from among \MODE LPT1=COM1 Appendix C Printer Specifications Printer Specifications Power consumption Power requirementsDimensions Weight Glossary First mode Cassette modeDpi dots per inch IEEE1284 MB mega byte Prescribe commandsMP tray Offline USB Universal Serial Bus Sleep modeStatus Index EcoPrint Glossary-2Emulation Glossary-2Envelope Index-3