Push it in all the way | Kyocera FS-1010 specification

Memory (CompactFlash) Card

If the Network Interface Card or the Serial Interface Board is installed

Remove the two screws from the network interface card or the serial interface board and remove it.

Network Interface Card

(or Serial Interface Board)

Screws

3	Insert the memory card in the slot. Insert as shown in the figure.
	Push it in all the way.

Memory Card

4	Close and secure the slot cover. If the network interface card or the
	serial interface board kit is removed in the step 2 above, reinstall

and secure the card or the kit.

A-9

Image 67

Kyocera FS-1010 manual Push it in all the way

Contents

Printer Regarding Tradenames General Limited WarrantyLicense Limitation of Remedies Agfa Japan License Agreement Guidelines Typeface Trademark Acknowledgement Contents Appendix B Host Computer Interface Paper SelectionFonts Appendix a Options Glossary-1 Appendix C Printer SpecificationsIndex-1 Introduction Description Guide to the Manuals Guide to the Operation Guide Basic Operations Operator Panel Reference Name Function IndicatorsKeys Reference Name Status Meaning Status Hardware Information Installation OptionsError Log Software Version Interface Information Toner GaugeKIR Test Pattern Maintenance Toner Container Replacement Interval Toner Container ReplacementToner Kit to be Used Replenishing Toner Take the new toner container from the bag. Hold it with Lock Lock position. Lock lever #2 is automatically locked Printer Interior Cleaning Never stand the process unit on end Slots in the printer Troubleshooting General Guide Symptom Check Items Corrective Action Contact your Kyocera Mita dealer Print Quality ProblemsClean the charger wire Printed Results Corrective Action Check the paper size setting Check the EcoPrint settingConfirm Toner indicator Try setting the thin paper mode Indicators Maintenance Messages After reinserting the paper cassette, you should be TheprintjobcannotbedoneatcurrentresolutionThere is no cassette in the feeder, or Cassette is not inserted properly Eraser error 5300 error Errors Requiring Service Personnel AttentionScanner motor error 4000 error Scanner pin-photo error 4200 error Waste toner reservoir is full ErrorNone Waste toner reservoir is full Error Controller RAM read/write error F020 error Engine ROM check sum error F050 error Communication error F040 error Error Messages Printer has halted because you attempted to insert Printer power is onMake sure to turn the printer power off before inserting This message appears when the printer is in the ready Indicator KM-NET for Clients display Description Normal Indicator Display Jam at the Face-down and Face-up Trays Correcting a Paper Jam Jam Inside the Printer Jam at the Paper Cassette Into the printer Paper Selection General Guidelines Paper SpecificationsSpecifications Specification Condition of the Paper Selecting the Right PaperComposition Smoothness Basis WeightPaper Size Paper Sizes for Paper Feeding Thickness Caliper Moisture ContentPaper Grain Other Paper Properties Special Paper Transparency SpecificationsTransparency overhead projection film Adhesive-backed label Adhesive-Backed Labels Preprinted Paper Adhesive Label SpecificationsEnvelopes Colored Paper Recycled Paper Paper Type Paper Source MP Tray Paper Weight Paper Type CassettePaper Type Fonts Internal Fonts Internal Scalable and Bitmap Fonts and Kpdl Fonts List of Fonts List of Fonts List of Fonts Font Kpdl Fonts List of Fonts Appendix a Options Memory CompactFlash Card Available Options YES Expansion Memory Installation Dimm to be used Installing the Dimm Insert the Dimm into the Dimm socket so that the notches on To remove a Dimm Testing the Expansion Memory Setting the Printer Driver Memory CompactFlash Card Push it in all the way Network Interface Card Appendix B Host Computer Interface Parallel Interface Interface SignalsParallel Interface Communication Modes Pin In/out Description Table B.1 Parallel Connector Pin Assignment Error* nFault Pin Data 0 1 to Data 7 8 Pins 2 toPaper Empty PError Pin Reset nInit Pin Select In nSelectIn Pin Power Ready Pin USB Interface Specifications 1 RS-232C Interface Serial Interface Option DTR Data Terminal Ready Pin SG Signal Ground PinTable B.4 RS-422A Signal Pin Assignments 2 RS-422A Interface SDB Send Data Pin SDA Send Data Inverted Pin Overview of Signals RS-422ASerial Connector RDB Receive Data Pin RDA Receive Data Inverted Pin H3 Stop bits RS-232C/RS-422A ProtocolH1 Baud rate H2 Data bits H7 Buffer nearly-empty threshold Prescribe Frpo D0 CommandH5 Protocol logic H6 Buffer nearly-full threshold RS-232C Cable Connection Connecting the Printer to the ComputerObtain a Suitable RS-232C Cable Cursor with Settings, then click on Control Panel from among \MODE LPT1=COM1 Appendix C Printer Specifications Printer Specifications Weight Power requirementsPower consumption Dimensions Glossary IEEE1284 Cassette modeFirst mode Dpi dots per inch Offline Prescribe commandsMB mega byte MP tray Status Sleep modeUSB Universal Serial Bus Index EcoPrint Glossary-2Emulation Glossary-2Envelope Index-3