Indicators

3.3.3Error Messages

With the following errors, printing continues when you press the printer’s key. You can confirm these errors by printing a status page. (See pages

1-4and 1-5.)

 

 

Indicator

KM-NET for

 

 

 

 

Corrective Action

 

 

 

 

 

Clients display

 

 

 

 

 

 

 

 

 

 

 

 

 

File not found

The specified file is not found.

 

 

 

 

 

 

 

Press GO

Press the

key to resume printing. You can abondon printing

 

 

 

 

 

 

by pressing the

key.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

KPDL Error

Current print processing cannot continue.

 

 

 

 

 

Press GO

Press the

key to resume printing. You can abandon printing

 

 

 

 

 

 

 

 

 

 

 

by pressing the

key.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MemoryCard err##

An error has occurred during access to the memory card

 

 

 

 

 

Press GO

using the PRESCRIBE RWER command or from the KM-

 

 

 

 

 

 

NET for Clients.

 

 

 

 

 

 

 

 

 

 

Look at the error code given in place of ## and refer to the

 

 

 

 

 

 

corresponding description given below.

 

 

 

 

 

 

 

 

04 :The capacity of the memory card is insufficient. Clean up

 

 

 

 

 

 

 

files.

 

 

 

 

 

 

 

 

 

 

 

05 :Specified file not on memory card.

 

 

 

 

 

 

 

 

06 :No memory for use by memory card. Expand printer memory.

 

 

 

 

 

 

Press the

key to resume printing. You can abandon printing

 

 

 

 

 

 

by pressing the

key.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Memory overflow

Printingcannotcontinuebecausethereisnotenoughmemory.

 

 

 

 

 

Press GO

Try adding more memory. Press the

key to resume printing.

 

 

 

 

 

 

You can abandon printing by pressing the

key.

 

 

 

 

 

Print overrun

Currentprintprocessingcannotcontinueduetocomplexdata.

 

 

 

 

 

Press GO

The data transferred to the printer was too complex to print on a

 

 

 

 

 

 

page. Press the

key to print data as far as it was stored. You

 

 

 

 

 

 

can abandon printing by the

key.

 

 

 

 

 

 

 

 

 

 

To release the page protect mode, send the following

 

 

 

 

 

 

 

 

command to the printer from the KM-NET for Clients

 

 

 

 

 

 

 

 

after this error occurs:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

!R! FRPO R5, 1; EXIT;

 

 

 

 

 

 

 

RAM DISK error ##

Check the error code displayed in ## and refer to the

 

 

 

 

 

Press GO

appropriate description below.

 

 

 

 

 

 

 

 

01: Abnormal format. Try turning the power off and on again.

 

 

 

 

 

 

02: RAM disk mode is Off. Turn RAM disk mode On.

 

 

 

 

 

 

04: No disk space. Clean up files.

 

 

 

 

 

 

 

 

05: Specified file is not on disk.

 

 

 

 

 

 

 

 

 

06: No memory for use by disk system. Expand printer memory.

 

 

 

 

 

 

 

 

 

 

 

 

 

(Continued on next page)

3-11

Page 35
Image 35
Kyocera FS-1010 manual Error Messages