Manuals / Kyocera / Computer Equipment / Printer

Kyocera FS-1010 manual Available Options, Memory CompactFlash Card

Models: FS-1010

1 93

Download 93 pages 8.47 Kb

Page 60

Available Options

A.1 Available Options

The following options are available for the printer:

Either the network interface card or the serial interface board can be installed in the printer.

PF-17 Paper Feeder

IB-10E Serial Interface Board Kit

Network Interface Card

Contact your Kyocera Mita dealer for information on purchasing the network interface card that is best suited for use with this printer.

Only network interface cards operating on DC 3.3 V can be used in this printer.

Memory (CompactFlash) Card

Contact your Kyocera Mita dealer for information on purchasing the memory card that is best suited for use with this printer.

A-2

Image 60

Kyocera FS-1010 manual Available Options, Memory CompactFlash Card

Contents

Printer Regarding Tradenames Limited Warranty LicenseLimitation of Remedies GeneralTypeface Trademark Acknowledgement Agfa Japan License Agreement GuidelinesContents Paper Selection FontsAppendix a Options Appendix B Host Computer InterfaceAppendix C Printer Specifications Glossary-1Index-1 Introduction Guide to the Manuals DescriptionGuide to the Operation Guide Basic Operations Operator Panel Indicators KeysReference Name Status Meaning Reference Name FunctionStatus Installation Options Error LogSoftware Version Hardware InformationToner Gauge Interface InformationKIR Test Pattern Maintenance Toner Container Replacement Toner Container Replacement IntervalToner Kit to be Used Replenishing Toner Take the new toner container from the bag. Hold it with Lock Lock position. Lock lever #2 is automatically locked Cleaning Printer InteriorNever stand the process unit on end Slots in the printer Troubleshooting Symptom Check Items Corrective Action General GuidePrint Quality Problems Clean the charger wirePrinted Results Corrective Action Contact your Kyocera Mita dealerCheck the EcoPrint setting Confirm Toner indicatorTry setting the thin paper mode Check the paper size settingIndicators Maintenance Messages Theprintjobcannotbedoneatcurrentresolution There is no cassette in the feeder, orCassette is not inserted properly After reinserting the paper cassette, you should beErrors Requiring Service Personnel Attention Scanner motor error 4000 errorScanner pin-photo error 4200 error Eraser error 5300 errorError None Waste toner reservoir is full ErrorController RAM read/write error F020 error Waste toner reservoir is fullCommunication error F040 error Engine ROM check sum error F050 errorError Messages Printer power is on Make sure to turn the printer power off before insertingThis message appears when the printer is in the ready Printer has halted because you attempted to insertNormal Indicator Display Indicator KM-NET for Clients display DescriptionCorrecting a Paper Jam Jam at the Face-down and Face-up TraysJam at the Paper Cassette Jam Inside the PrinterInto the printer Paper Selection Paper Specifications SpecificationsSpecification General GuidelinesSelecting the Right Paper Condition of the PaperComposition Basis Weight Paper SizePaper Sizes for Paper Feeding SmoothnessMoisture Content Thickness CaliperPaper Grain Other Paper Properties Transparency Specifications Special PaperTransparency overhead projection film Adhesive-Backed Labels Adhesive-backed labelAdhesive Label Specifications EnvelopesColored Paper Preprinted PaperRecycled Paper Paper Source MP Tray Paper Weight Paper Type Cassette Paper TypePaper Type Fonts Internal Fonts List of Fonts Internal Scalable and Bitmap Fonts and Kpdl FontsList of Fonts List of Fonts Font Kpdl Fonts List of Fonts Appendix a Options Available Options Memory CompactFlash CardExpansion Memory Installation YESInstalling the Dimm Dimm to be usedInsert the Dimm into the Dimm socket so that the notches on Testing the Expansion Memory To remove a DimmSetting the Printer Driver Memory CompactFlash Card Push it in all the way Network Interface Card Appendix B Host Computer Interface Interface Signals Parallel InterfaceParallel Interface Communication Modes Table B.1 Parallel Connector Pin Assignment Pin In/out DescriptionData 0 1 to Data 7 8 Pins 2 to Paper Empty PError PinReset nInit Pin Error* nFault PinPower Ready Pin Select In nSelectIn PinSpecifications USB InterfaceSerial Interface Option 1 RS-232C InterfaceSG Signal Ground Pin Table B.4 RS-422A Signal Pin Assignments2 RS-422A Interface DTR Data Terminal Ready PinOverview of Signals RS-422A Serial ConnectorRDB Receive Data Pin RDA Receive Data Inverted Pin SDB Send Data Pin SDA Send Data Inverted PinRS-232C/RS-422A Protocol H1 Baud rateH2 Data bits H3 Stop bitsPrescribe Frpo D0 Command H5 Protocol logicH6 Buffer nearly-full threshold H7 Buffer nearly-empty thresholdConnecting the Printer to the Computer RS-232C Cable ConnectionObtain a Suitable RS-232C Cable Cursor with Settings, then click on Control Panel from among \MODE LPT1=COM1 Appendix C Printer Specifications Printer Specifications Power requirements Power consumptionDimensions WeightGlossary Cassette mode First modeDpi dots per inch IEEE1284Prescribe commands MB mega byteMP tray OfflineSleep mode StatusUSB Universal Serial Bus Index EcoPrint Glossary-2Emulation Glossary-2Envelope Index-3