Manuals / Kyocera / Computer Equipment / Printer

Kyocera FS-1010 manual Memory CompactFlash Card

Models: FS-1010

1 93

Download 93 pages 8.47 Kb

Page 66

Memory (CompactFlash) Card

A.3 Memory (CompactFlash) Card

Insert the memory (CF) card into the card slot located on the rear of the printer. A memory card is a microchip card that may contain option fonts, macros, forms, etc. The printer reads the contents of the card into its internal memory when printer is turned on. The presence of this data in the printer memory can be confirmed on the status page printout.

For details of available memory cards, contact your Kyocera Mita dealer.

1 Turn off the printer.

Never insert or remove a memory card while the printer power is on. Failure to turn the power switch off will immediately halt the printer with the four indicators turned on. It also could result in damage to the printer’s electronic parts or the memory card. Turn the power switch on again to restart the printer.

2	Remove the two screws from the option interface slot cover and
	remove the slot cover.

Option Interface Slot Cover

Screws

A-8

Image 66

Kyocera FS-1010 manual Memory CompactFlash Card

Contents

Printer Regarding Tradenames Limitation of Remedies Limited WarrantyLicense GeneralTypeface Trademark Acknowledgement Agfa Japan License Agreement GuidelinesContents Appendix a Options Paper SelectionFonts Appendix B Host Computer InterfaceAppendix C Printer Specifications Glossary-1Index-1 Introduction Guide to the Manuals DescriptionGuide to the Operation Guide Basic Operations Operator Panel Reference Name Status Meaning IndicatorsKeys Reference Name FunctionStatus Software Version Installation OptionsError Log Hardware InformationToner Gauge Interface InformationKIR Test Pattern Maintenance Toner Container Replacement Toner Container Replacement IntervalToner Kit to be Used Replenishing Toner Take the new toner container from the bag. Hold it with Lock Lock position. Lock lever #2 is automatically locked Cleaning Printer InteriorNever stand the process unit on end Slots in the printer Troubleshooting Symptom Check Items Corrective Action General GuidePrinted Results Corrective Action Print Quality ProblemsClean the charger wire Contact your Kyocera Mita dealerTry setting the thin paper mode Check the EcoPrint settingConfirm Toner indicator Check the paper size settingIndicators Maintenance Messages Cassette is not inserted properly TheprintjobcannotbedoneatcurrentresolutionThere is no cassette in the feeder, or After reinserting the paper cassette, you should beScanner pin-photo error 4200 error Errors Requiring Service Personnel AttentionScanner motor error 4000 error Eraser error 5300 errorController RAM read/write error F020 error ErrorNone Waste toner reservoir is full Error Waste toner reservoir is fullCommunication error F040 error Engine ROM check sum error F050 errorError Messages This message appears when the printer is in the ready Printer power is onMake sure to turn the printer power off before inserting Printer has halted because you attempted to insertNormal Indicator Display Indicator KM-NET for Clients display DescriptionCorrecting a Paper Jam Jam at the Face-down and Face-up TraysJam at the Paper Cassette Jam Inside the PrinterInto the printer Paper Selection Specification Paper SpecificationsSpecifications General GuidelinesSelecting the Right Paper Condition of the PaperComposition Paper Sizes for Paper Feeding Basis WeightPaper Size SmoothnessMoisture Content Thickness CaliperPaper Grain Other Paper Properties Transparency Specifications Special PaperTransparency overhead projection film Adhesive-Backed Labels Adhesive-backed labelColored Paper Adhesive Label SpecificationsEnvelopes Preprinted PaperRecycled Paper Paper Source MP Tray Paper Weight Paper Type Cassette Paper TypePaper Type Fonts Internal Fonts List of Fonts Internal Scalable and Bitmap Fonts and Kpdl FontsList of Fonts List of Fonts Font Kpdl Fonts List of Fonts Appendix a Options Available Options Memory CompactFlash CardExpansion Memory Installation YESInstalling the Dimm Dimm to be usedInsert the Dimm into the Dimm socket so that the notches on Testing the Expansion Memory To remove a DimmSetting the Printer Driver Memory CompactFlash Card Push it in all the way Network Interface Card Appendix B Host Computer Interface Interface Signals Parallel InterfaceParallel Interface Communication Modes Table B.1 Parallel Connector Pin Assignment Pin In/out DescriptionReset nInit Pin Data 0 1 to Data 7 8 Pins 2 toPaper Empty PError Pin Error* nFault PinPower Ready Pin Select In nSelectIn PinSpecifications USB InterfaceSerial Interface Option 1 RS-232C Interface2 RS-422A Interface SG Signal Ground PinTable B.4 RS-422A Signal Pin Assignments DTR Data Terminal Ready PinRDB Receive Data Pin RDA Receive Data Inverted Pin Overview of Signals RS-422ASerial Connector SDB Send Data Pin SDA Send Data Inverted PinH2 Data bits RS-232C/RS-422A ProtocolH1 Baud rate H3 Stop bitsH6 Buffer nearly-full threshold Prescribe Frpo D0 CommandH5 Protocol logic H7 Buffer nearly-empty thresholdConnecting the Printer to the Computer RS-232C Cable ConnectionObtain a Suitable RS-232C Cable Cursor with Settings, then click on Control Panel from among \MODE LPT1=COM1 Appendix C Printer Specifications Printer Specifications Dimensions Power requirementsPower consumption WeightGlossary Dpi dots per inch Cassette modeFirst mode IEEE1284MP tray Prescribe commandsMB mega byte OfflineSleep mode StatusUSB Universal Serial Bus Index EcoPrint Glossary-2Emulation Glossary-2Envelope Index-3