Prior to lighting your appliance:

qReview the safety precautions section.

qReview the pellet FUEL section.

qReview and follow the Operating Instructions.

qPlug power cord connector into corresponding connector on the back of appliance (see Figures 7 and 8 showing connector locations).

After you have begun operation of your appliance:

qReview the routine cleaning / maintenance information.

qEnjoy the warmth from your new Lennox Hearth Products pellet stove!

Damper Location, Installation And Adjustment

Damper Air Control

Located behind the right side panel on model Montage 32FS.

Adjustment Procedure

Using a 1/4" nut driver or socket, loosen the damper setscrew (see Figure 6). Adjust in 1/4” increments until optimum combustion air flow is achieved. Retighten the damper setscrew.

For less air push in and for more air pull out.

Loosen Setscrew

Standard Settingto Adjust Damper 3/4" (19mm)

Damper

Figure 6 - Damper Adjustment

IMPORTANT NOTE: Install the thermostat per the manufacturers instruc- tions, provided with the thermostat. Failure to follow manufacturers instructions could result in a malfunction. Pay special attention to the thermostat location requirements. If the location requirements are not adhered to the appliance, erratic operation or failure may occur.

Do not mount the thermostat where it may be affected by:

Radiant heat from the stove, fireplaces, sun or other heat sources.

Drafts or dead spots behind doors or in corners.

Hot or cold air from ducts.

Thermostat Installation:

Note: Always Disconnect Power Before Performing The Thermostat Installation.

A 24 volt wall thermostat and 20 feet of 18-gage thermostat wire is included in the accessory package. It is recommended that the thermostat and thermostat wire be installed by an Lennox Hearth Products dealer.

Thermostat wires and purple wires from wire har- ness will connect to these 2 terminals

Jumper

Route thermostat wires

Remove jumper if Thermostat IS to be used

through this grommet

Leave jumper on, if thermostat is NOT used

 

Figure 7 - Terminal Block

Installation Steps:

1.Unplug stove power cord from the wall outlet.

2.Locate the thermostat terminal block (see Figures 7 and 8).

3.Loosen the two terminal screws on the terminal block and remove the jumper.

4.Connect the two wires from your thermostat to the terminals (one per terminal). Ensure that the purple wires from the harness remain connected to the terminal block and tighten the terminal screws. Make sure the wires are firmly connected to the thermostat.

5.Plug in the stove and you are ready to operate with your thermo- stat!

Note: See Wiring Diagram on Page 27.

IMPORTANT

If the wall thermostat provided is not used, the jumper is required for the stove to operate.

Figure 8 - Terminal Block Location

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

Page 9
Image 9
Lennox Hearth 32FS operation manual Damper Location, Installation And Adjustment

32FS specifications

The Lennox Hearth 32FS is an exceptional fireplace designed to enhance both the aesthetic and functional aspects of any home. With its innovative technologies and user-friendly features, this model stands out as a premier choice for those looking to introduce warmth and elegance into their living space.

One of the primary features of the Lennox Hearth 32FS is its impressive heating capacity. With a BTU output that provides efficient heating to large areas, this fireplace is perfect for open floor plans or vast living rooms. This capability ensures that the space remains cozy and inviting even in the coldest months.

The combustion technology integrated into the Lennox Hearth 32FS is noteworthy as well. Utilizing a clean-burning system, it maximizes heat output while minimizing emissions, making it an environmentally-friendly option. The glass door design enhances air regulation and combustion efficiency, ensuring that homeowners get the most out of each burning cycle.

Another characteristic that sets the 32FS apart is its aesthetic appeal. The fireplace features a sleek and modern design, allowing it to blend seamlessly into various home decors, from traditional to contemporary. Customizable options, including different front designs and surround materials, allow homeowners to choose a look that aligns with their personal style.

Additionally, the Lennox Hearth 32FS provides ease of use and control. The model comes equipped with an intuitive remote control system, allowing users to adjust settings without leaving their seat. Whether it’s adjusting the flame height or configuring the thermostat, the convenience provided by this technology is undeniable.

Durability and build quality are other prominent aspects of the Lennox Hearth 32FS. Constructed from high-quality materials, it is designed to withstand the test of time, ensuring consistent performance year after year. The fireplace’s design includes advanced insulation techniques, which not only enhances efficiency but also ensures safety during operation.

In summary, the Lennox Hearth 32FS is a sophisticated fireplace featuring advanced heating capabilities, clean combustion technology, and a stylish design that caters to varying tastes. Its user-friendly controls and durable construction make it a reliable choice for anyone looking to invest in an energy-efficient heating solution that adds charm and comfort to their home.