LG Electronics 32LD333H, 42LD343H, 37LD343H, 26LD343H LT2002 Cloning Notes, LT2002 Clone Programmer

Cloning Procedures (Cont.)

Learning / Teaching a Master TV Setup using an LT2002 Clone Programmer

Warning: Do not connect a clone programmer to a PPV card installed in the Master or Target TVs. Also, if the TV is in LodgeNet PPV Mode (check with the site administrator if you are not certain), do not connect a clone programmer to the GAME CONTROL/MPI port. Either of these actions will damage the clone programmer and, if applicable, the PPV card.

Cloning is accomplished using the TV/
clone programmer MPI ports for com-
munication (see figure).	Antenna
LT2002 Cloning Notes	or CATV

MPI

Cable

• Read the IMPORTANT CLONING INFORMATION on page 27 before beginning any cloning procedures.

• A slow ashing green light indicates that there are communication problems between the TV and the LT2002 clone programmer. If this is the case, check for a damaged cable, poor contacts, or other connection troubles.

•If the status indicator is red, the LT2002 batteries are low and should be re-

placed. Install four (4) high-quality alkaline AA batteries.

•Learning and Teaching is only possible between identical model TVs; however, the LT2002 clone programmer can store up to three different Master TV Setups.

THE CLONE HAS CONTROL OF THE TV

THE CLONE IS VERSION XX

THE TV IS VERSION XX

THE SW IS REViSION XX

CLONE CLOCK = XX:XX

TV CLOCK = XX:XX

- PRESS ANY KEY TO CONTINUE

Ferrite Core (TDK, ZCAT 2035-0930)

LT2002 Clone Programmer

$POOFDU DBCMF UP
57 .1* +BDL BOE	Status
GPMMPX PO TDSFFO
instructions	*OEJDBUPS

MPI

Reset

$PMPS

t
HSFFO






CBUUFSZ
PL

t
SFE




CBUUFSZ
MPX

#MJOL
QBUUFSO t
TMPX







QPXFS
PO

no communications

t
IFBSUCFBU


QPXFS
PO

communications ok

®

QuickSet II Programmer

LT2002

ZENITH ELECTRONICS CORPORATION, LINCOLNSHIRE, ILLINOIS, USA

Learn Setup from Master TV

1.Ensure the Master TV is set up completely and the EBL is in Pass- through Mode.

2.If an analog channel is not available, direct tune the TV to an Aux source, or select an Aux source, such as AV-1, from the Input Menu. Then, plug one end of the MPI cable into the TV MPI port.

3.If there is a good connection after the LT2002 is connected to the TV MPI port, “THE CLONE HAS CONTROL OF THE TV” message will appear on the TV screen. Press any key on the Installer Remote to access the LT2002 Clone Selection Menu.

4.Press 1 on the Installer Remote to select LEARN FROM TV from the Clone Selection Menu; then press ENTER to proceed to the Memory Bank Selection Menu (see sample screen on next page).

5.Select the clone Memory Bank in which to store the Master Setup by pressing either Channel key repeatedly to choose Memory Bank 1, 2, or 3. Note: If you choose a Memory Bank that already has a Master device’s setup programmed into it, that setup will be overwritten by the new Master TV Setup.

(Continued on next page)

THE CLONE HAS CONTROL OF THE TV

THE CLONE IS VERSION XX

THE TV IS VERSION		XX
THE SW IS REVISION		XX
CLONE CLOCK = XX:XX
TV	CLOCK = XX:XX

-PRESS ANY KEY TO CONTINUE.

-DISCONNECT CLONE WHEN DONE.

CLONE SELECTION MENU

(1) LEARN FROM TV

(2)TEACH TO TV

(3)SET CLONE CLOCK FROM TV

(4)SET TV CLOCK FROM CLONE

(5)DISPLAY TV SETUP

(6)DISPLAY CLONE SETUP

-TO CHANGE MENU ITEMS, PRESS CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER.

206-4163 31