LG Electronics 37LD333H, 42LD343H, 37LD343H, 26LD343H LT2002 Cloning Notes, LT2002 Clone Programmer

Cloning Procedures (Cont.)

Learning / Teaching a Master TV Setup using an LT2002 Clone Programmer

Warning: Do not connect a clone programmer to a PPV card installed in the Master or Target TVs. Also, if the TV is in LodgeNet PPV Mode (check with the site administrator if you are not certain), do not connect a clone programmer to the GAME CONTROL/MPI port. Either of these actions will damage the clone programmer and, if applicable, the PPV card.

Cloning is accomplished using the TV/ clone programmer MPI ports for com- munication (see figure).

LT2002 Cloning Notes

Antenna or CATV

MPI

Cable

• Read the IMPORTANT CLONING INFORMATION on page 23 before beginning any cloning procedures.

•A slow flashing green light indicates that there are communication problems between the TV and the LT2002 clone programmer. If this is the case, check for a damaged cable, poor contacts, or other connection troubles.

•If the status indicator is red, the LT2002 batteries are low and should be re- placed. Install four (4) high-quality

alkaline AA batteries.

•Learning and Teaching is only possible between identical model TVs; however, the LT2002 clone programmer can store up to three different Master TV Setups.

THE CLONE HAS CONTROL OF THE TV

THE CLONE IS VERSION XX

THE TV IS VERSION XX

THE SW IS REViSION XX

CLONE CLOCK = XX:XX

TV CLOCK = XX:XX

- PRESS ANY KEY TO CONTINUE

Ferrite Core (TDK, ZCAT 2035-0930)

LT2002 Clone Programmer

Connect cable to
TV MPI Jack and		Status
follow on screen
instructions		Indicator
	MPI
				Reset
			Color
	• green		battery ok
	• red		battery low
		Blink pattern
	• slow		power on

no communications

•heartbeat power on communications ok

®

QuickSet II Programmer

LT2002

ZENITH ELECTRONICS CORPORATION, LINCOLNSHIRE, ILLINOIS, USA

Learn Setup from Master TV

THE CLONE HAS CONTROL OF THE TV

1.Ensure the Master TV is set up completely and in Pass-through Mode.

2.If an analog channel is not available, direct tune the TV to an Aux source, or select an Aux source, such as AV-1, from the Input Menu. Then, plug one end of the MPI cable into the TV MPI port.

3.If there is a good connection after the LT2002 is connected to the TV MPI port, “THE CLONE HAS CONTROL OF THE TV” message will

appear on the TV screen. Press any key on the Installer Remote to access the LT2002 Clone Selection Menu.

THE CLONE IS VERSION XX

THE TV IS VERSION		XX
THE SW IS REVISION		XX
CLONE CLOCK = XX:XX
TV	CLOCK = XX:XX

-PRESS ANY KEY TO CONTINUE.

-DISCONNECT CLONE WHEN DONE.

4.Press 1 on the Installer Remote to select LEARN FROM TV from the Clone Selection Menu; then press ENTER to proceed to the Memory Bank Selection Menu (see sample screen on next page).

5.Press 1, 2, or 3 on the Installer Remote to select the clone Memory Bank in which to store the Master Setup. Then, press ENTER.

Note: If you choose a Memory Bank that already has a Master device’s setup programmed into it, that setup will be overwritten by the new Master TV Setup.

(Continued on next page)

CLONE SELECTION MENU

(1) LEARN FROM TV

(2)TEACH TO TV

(3)SET CLONE CLOCK FROM TV

(4)SET TV CLOCK FROM CLONE

(5)DISPLAY TV SETUP

(6)DISPLAY CLONE SETUP

-TO CHANGE MENU ITEMS, PRESS CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER.

206-4186 27