Adding a Helios Rectifier 100/48

1. Remove the rectifier blank panel and store it for future use.

Note: Should a rectifier be removed at any time, re-install the blank panel to meet the regulatory requirements.

2.Verify that the AC, DC and signalling cabling for the rectifier shelf has been previously installed and verified.

3.Ensure that the AC and DC circuit breakers on the front panel of the rectifier are in the OFF position.

4.Carefully slide the rectifier into position, making sure that it is fully inserted.

5.Install the left and right side clamping brackets supplied with the rectifier to secure it into position.

6.Operate the AC circuit breaker of the new rectifier to the “ON” position.

7.With the DC breaker in the “OFF” position, adjust the float, equalize and high voltage shutdown voltage levels as required. Refer to the appropriate rectifier user manual (see 6.0 -

Reference Documents).

8.Install the corresponding sense fuse (RC) on the front of the controller.

9.Ensure that the FLS/FS switch on the rectifier is set to the same position as that of the other rectifiers in the power system.

10.Operate the DC circuit breaker of the rectifier to the “ON” position.

11.Verify that the rectifier is sharing the load by observing its ammeter. It should display approximately the same value as the ammeters on the other rectifiers. If not, adjust its float and equalize voltage levels as described in the appropriate rectifier user manual (see 6.0 -

Reference Documents).

Adding a Helios Rectifier 200I/48 or 200E/48

1.Ensure that the AC and DC circuit breakers on the front panel of the rectifier are in the OFF position.

2.Use a manual lift (or at least two people) to lift the rectifier to its position, rest it on the angle guides, and slide it into the cabinet.

3.Align the mounting holes of the rectifier with those of the cabinet uprights and secure the rectifier in place using the eight mounting screws provided.

Note: A star washer must be used on one of the mounting screws.

4.Bring the connectorized AC cord up (top fed) or down (bottom fed) the cabinet and secure as required.

5.Install the required circuit breaker at the AC service panel.

6.Ensure that the circuit breaker installed per Step 5 is locked in the open (OFF) position.

7.Determine the length of cable (or individual wires in conduit) required to bring the AC supply from the AC service panel to the rectifier cabinet.

8.Cut the cable (or wires) to the required lengths then run and secure between the AC service panel and the rectifier cabinet.

9.Strip the sheeting and insulation material away from the ends of the wires to expose the AC leads

10.For a Helios Rectifier 200E/48 without an AC cord, remove the AC protective cover at the rear of the rectifier and connect the AC leads inside the rectifier as shown in Figure 32, then reinstall the AC protective cover.

For a Helios Rectifier 200E/48 or a Helios Rectifier 200I/48 equipped with an AC cord, first connect the associated female receptacle supplied with the rectifier to the cable (or wires) incoming from the AC service panel (refer to Figure 33). Then, plug the male connector at the end of the rectifier AC cord into the female receptacle.

For a Helios Rectifier 200E/48 equipped with an AC cord, feed the cables through the appro- priate strain relief connector at the top (top fed) or bottom (bottom fed) of the rectifier AC junction box inside the cabinet (refer to Figure 34). Use a flat blade screwdriver to tighten the strain relief connector, then connect the wires to the appropriate terminals inside the junction box as shown in Figure 34. Use plastic cable ties to secure the wires at the tie down points (one for each rectifier position) inside the junction box. Plug the male connector at the

Maintenance 41

Page 47
Image 47
Liebert 1500, 3000, 4000, 6000 A user manual Adding a Helios Rectifier 100/48, Adding a Helios Rectifier 200I/48 or 200E/48

1500, 6000 A, 4000, 3000 specifications

The Liebert 3000 is a cutting-edge power protection solution designed to provide reliable and efficient backup power for critical applications. This uninterruptible power supply (UPS) system is engineered to safeguard sensitive electronic equipment from power disturbances, ensuring uninterrupted operations in data centers, telecommunications, and industrial environments.

One of the standout features of the Liebert 3000 is its high-efficiency design. With an efficiency rating of up to 94%, the system minimizes energy loss, resulting in lower operational costs and a reduced carbon footprint. This is particularly important in today's environmentally conscious climate, as organizations strive to meet sustainability goals while maintaining top-tier performance.

The Liebert 3000 employs advanced technologies to enhance its functionality. It incorporates online double-conversion technology, which provides a continuous supply of clean and regulated power. This technology ensures that connected loads receive stable voltage and frequency, shielding them from voltage spikes, sags, and outages. Additionally, the UPS offers features such as automatic battery testing, which helps ensure peak battery performance and reliability.

Another key characteristic of the Liebert 3000 is its modular design, allowing for flexible scalability. This means that organizations can easily expand the capacity of their UPS system as their power needs grow, without the need for extensive system overhauls. The modular architecture also facilitates simplified maintenance and reduces downtime, as individual modules can be serviced without interrupting power to the critical load.

The system is equipped with comprehensive monitoring and management capabilities. The Liebert 3000 provides real-time data on power usage, battery status, and system performance, enabling facility managers to make informed decisions and proactively address potential issues. The integration of remote management tools allows for seamless monitoring from anywhere, providing peace of mind for operators.

Overall, the Liebert 3000 combines high efficiency, advanced technology, and flexible design to deliver a robust power protection solution. Its reliability and performance make it a preferred choice for organizations seeking to protect their critical infrastructure while enhancing operational efficiency and sustainability. As businesses continue to rely on technology for their everyday operations, the Liebert 3000 stands out as a dependable safeguard against the uncertainties of power quality.