Liebert Series 610

Operating Instructions

Figure 8 Power-Tie system one-line diagram

Contents

Main C ONTINUOUS P OWER -T IE C Page TABLE OF CONTENTS FIGURES 1.0 SYSTEM DESCRIPTION 1.1 Function 1.2 System Flexibility 1.3 Inter-System Isolation and Reliability Page Page Page 1.4 Control System Features Digital Controls Digital Phase Lock of Uninterruptible Power Module (UPM) Inverters System Output Voltage Control Module Load Sharing 1.5.2 Momentary Tie Operation Intersystem Synchronizing Momentary Tie Transfer Controls 1.5.3 Continuous Tie Intersystem Sync and Power Sharing Continuous Tie/Transfer/Parallel Control 1.5.4 Tie System Components 1.5.5 Modes of Operation Page 2.0 OPERATION DESCRIPTION 2.1 Continuous Power-Tie Selecting a Line Sync Source Synchronizing the UPS Systems Checking for Phase, Voltage, and Capacity Page 2.2 Separating Tied Systems Synchronize Systems Verifying Capacity OK to Open Tie 2.3 Load Transfers Between UPS Systems 2.4 Combined Loads on One System from Continuous Tie Operation 2.5 Combined Loads on One System to Continuous Tie Operation 2.6 Design Criteria Isolation and Fault Tolerance Load Share Signal Line Sync Signal Page Page 2.7 Improper User Operation Transfer Operation Tie Operation 2.8 Tie Circuit Breaker or Logic Faults 2.8.1 What Happens If a Failure Occurs During a Power Transfer 2.8.2 What Happens If a Logic Failure Occurs During Power Transfer 2.8.3 Hardware Failures 2.9 Recommendations - Tie Circuit Breaker Selection 3.0 CONTROL PANEL DESCRIPTION 3.1 Mimic Panel UPS System 1 - Primary Bypass UPS System 2 - Primary Bypass UPS System 1 - On Bypass 3.2 Load Transfer Controls Page 3.3 Continuous Tie Control 3.4 Control Inhibits 3.5 Manual Controls 4.0 OPERATING INSTRUCTIONS 4.1 Initial System Start-Up 4.2 Basic Operation 4.2.1 Momentary Tie - Load Transfers 4.2.2 Normal Transfer Operation Configurations 4.2.4 Isolating a UPS System for Maintenance - Combined Loads Operation 4.2.5 Transfer of Load Between Two Systems 4.2.6 Returning an Isolated System to Normal Operation - End Combined Loads Operation 4.2.7 Maintenance Procedures - Maintaining Power-Tie Components 4.2.8 Maintenance Procedures - Tie Control Logic Components 4.2.9 Abnormal Operations 4.2.10 Trouble Recovery 4.2.11 Continuous Tie-Systems Normal Operating Configuration Tying the UPS Systems - Continuous Parallel Operations Returning Parallel Systems to Normal Operation - End Continuous Tie Maintenance Procedures - Tie Control Logic and Power Components Abnormal Operations Trouble Recovery 4.2.12 Isolation for Maintenance Page 4.2.13 Operation Scenarios/Transfer Procedures See 4.1 - Initial System Start-Up. Figure 11 From continuous tied systems to loads split between two systems Figure 10 From combined loads operation to loads split between two feeders See 4.2.6 - Returning an Isolated System to Normal Operation - End Combined Loads Operation. Figure 12 Transfer both load feeders to one UPS Figure 13 Both feeders on one system to normal operation Figure 14 Transfer 100% load on one system to 100% load on a second system (a two-step operation) See 4.2.4 - Isolating a UPS System for Maintenance - Combined Loads Operation. See 4.2.6 - Returning an Isolated System to Normal Operation - End Combined Loads Operation. Figure 15 Normal split load operations to Continuous Tie Figure 16 Continuous Tie to normal split load operation Figure 17 Continuous Tie to load on one system See 4.2.11 - Tying the UPS Systems - Continuous Parallel Operations. See 4.2.11 - Returning Parallel Systems to Normal Operation - End Continuous Tie. Figure 18 Load on one system to Continuous Tie Figure 19 One system in bypass to both feeders combined on remaining operational system See 4.2.11 - Tying the UPS Systems - Continuous Parallel Operations. See 4.2.3 - Maintenance Procedures - Isolating Each UPS System. Figure 20 One system in bypass to Continuous Tie operation (Option 1) Figure 21 One system in bypass to Continuous Tie operation (Option 2) Page Page The Company Behind the Products Technical Support/Service Locations POWER AVAILABILITY C ONTINUOUS P OWER -T IE C U SER M