Operating Instructions
4.2.13Operation Scenarios/Transfer Procedures
Refer to the section listed below each figure for the operational procedure to perform the function indicated.
Figure 9 From start-up to normal operation, loads to be split between two distribution feeders
| FROM: |
| TO: |
Initial Conditions Prior to Startup | Normal Operation | ||
System 1 | System 2 | System 1 | System 2 |
M2
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
M1 |
| M1 |
| SS1 |
| SS2 |
| M2 |
| M2 | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Tie Open 
Tie
Load 1 Load 2
LEGEND: Mx = Module
SSx = Static Bypass Switch
Figure 10 From combined loads operation to loads split between two feeders
M1
FROM:
Combined Loads Operation
System 1 |
|
|
|
|
| System 2 | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| M1 |
| SS1 |
| SS2 |
| M2 |
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
M2
M1
TO:
Normal Operation
System 1 |
|
|
|
|
| System 2 | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| M1 |
| SS1 |
| SS2 |
| M2 |
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
M2
Tie |
Tie Closed | Tie Open |
| Tie |
Load 1 Load 2Load 1 Load 2
See 4.2.6 - Returning an Isolated System to Normal | LEGEND: Mx = | Module |
Operation - End Combined Loads Operation. | SSx = | Static Bypass Switch |
Figure 11 From continuous tied systems to loads split between two systems
M1
FROM:
Continuous Tied Systems
System 1 |
|
|
|
|
| System 2 | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| M1 |
| SS1 |
| SS2 |
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
M2
M1
TO:
Normal Operation
System 1 |
|
|
|
|
| System 2 | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| M1 |
| SS1 |
| SS2 |
| M2 |
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
M2
Continuous Tie operation for module out of service
| Tie Closed | Tie Open |
|
Tie | Tie | ||
Load 1 | Load 2 | Load 1 | Load 2 |
See 4.2.11 - Returning Parallel Systems to Normal | LEGEND: Mx = | Module |
Operation - End Continuous Tie. | SSx = | Static Bypass Switch |
33
