LightSpeed Technologies X12, Delta X10 manual Detailed Operation Wireless Receiver

VOL

7100R

UHF TRUE

DIVERSITY

LightSPEED RECEIVER

PWR Min Max

A B

CHANNEL

LOW

BAT RF SCAN SQ

Delta X10

						Wireless
					Sound System
WIRELESS MIC 1					WIRELESS MIC 2
					REPEAT	A — B	STOP		PLAY/PAUSE PROG
		CD-ROM ART GOES HERE
NO diSC					EJECT	— SKIP —				SCAN/SEARCH
LINE	LINE/CD LEVEL		VOICE OVER MUSIC				TONE CONTROL
I							0			0
N
O
U			-dB40	dB0		–			+	– HIGH +
T	min	max					LOW
IN	LEVEL					IN	LEVEL
1			LOW CUT							LOW CUT	2
MIC			music speech							music speech	MIC
	min	max				min			max
MASTER			BATTERY				LOW CUT			LOW CUT
VOLUME			STATUS
LIMIT						music		speech		music speech
	min	max			LOW OK	WIRELESS				WIRELESS
	LEVEL						MIC 1			MIC 2
EXTERNAL
SPEAKER A
SWITCHED
8 OHM
EXTERNAL			LightSPEED							CHARGING STATUS
SPEAKER B			MADE IN EUROPE			EXTERNAL
8 OHM
							POWER
						SOURCE
							12VDC/4A
							4	1
ON MUTE							3 2		GND
							+ 12V
POWER		DO NOT OPEN			ACTIVE		MAINS
			THE COVER.		LINK		AC
	ON	REFER SERVICING					90-264V
		TO QUALIFIED
	OFF		PERSONNEL.				47-63Hz
		REPLACE FUSE					FUSE
			ONLY WITH
	MUTE	THE SAME TYPE					T2A
			AND RATING.

		Operating Instructions
			Wireless Receiver(s)
Frequency Group		Volume
4		3
		VOL
	7100R
	UHF TRUE
	DIVERSITY
LightSPEED RECEIVER
		PWR Min	Max
	A	B
CHANNEL
LOW	RF	SCAN SQ
BAT
Manual Channel		5
Select Buttons		SCAN
EXTERNAL
SPEAKER A
SWITCHED
8 OHM
EXTERNAL		LightSPEED				CHARGING STATUS
SPEAKER B		MADE IN EUROPE		EXTERNAL
8 OHM
				POWER
				SOURCE
				12VDC/4A
				4	1
ON MUTE				3	2	GND
				+ 12V
POWER		DO NOT OPEN	ACTIVE	MAINS
		THE COVER.	LINK		AC
ON	REFER SERVICING			90-264V
		TO QUALIFIED		47-63Hz

FUSE

T2A

2 1

DETAILED OPERATION - WIRELESS RECEIVER

Power up the Delta X system and wireless receiver(s)

1.POWER: Push the POWER switch on the base unit back panel to the ON (or MUTE) position.

2.ON LED: The ON LED will light.

3.Receiver Volume: Rotate the Power/Volume knob on the receiver module clockwise to turn on. Leave the volume at a low level for now.

4.Frequency Group: When the receiver power is first switched on, the frequency group of the receiver will be shown briefly as letters on the LED display. (See frequency group chart on page 30)

Channel Selection - Wireless Receiver

Each receiver has 100 user-selectable channels to choose from. You can select a channel either manually or by pressing the SCAN button which will automatically select a clear channel.

5.Clear Channel Scan (Recommended): Make sure the transmitter(s) is OFF before pressing this button. When this button is pressed, the receiver will cycle through all 100 channels and select a clear frequency (this process takes about 20 seconds). Once the receiver selects the clear channel, you will need to select the same channel on the corresponding transmitter (handheld or belt-pack).

If You Have a Second Receiver (WIRELESS MIC 2): Verify that WIRELESS MIC 1 is operating on a clear channel, and the transmitter for WIRELESS MIC 1 is turned ON. Make sure the transmitter for WIRELESS MIC 2 is turned OFF, and then press the “SCAN” button on the WIRELESS MIC 2 receiver. After the WIRELESS MIC 2 receiver selects a clear channel, set the WIRELESS MIC 2 transmitter (handheld or belt-pack) to the selected channel.

LightSPEED Technologies • Wireless Sound Solutions • Toll Free: 1-800-840-3662 18