Change Or harness disconnected from | Lincoln Electric IM613-B

E-7		TROUBLESHOOTING	E-7

	Observe all Safety Guidelines detailed throughout this manual
	PROBLEMS	POSSIBLE CAUSE	RECOMMENDED
	(SYMPTOMS)	POSSIBLE CAUSE	COURSE OF ACTION
	(SYMPTOMS)		COURSE OF ACTION

14. Displays and/or indicator lights		a. The encoders or switches may be	If all recommended possible areas of
do not change when their corre-		faulty.	misadjustment have been checked
sponding switches and or knobs			and the problem persists, Contact
are activated to request a		b. Check for broken harness wire(s)	your local Lincoln Authorized
change.		or harness disconnected from	Field Service Facility.
		intended location.

CAUTION

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.

POWER FEED 11

Image 41

Lincoln Electric IM613-B manual Change Or harness disconnected from

Contents

IM613-B Safety Depends on You Safety Electric Shock can kill Iii Safety Sûreté Pour Soudage a L’Arc Précautions DE Sûreté Thank You Table of Contents P315 Series Section ESection F Power Feed Installation Wire Feeder to Power Source Configurations Safety PrecautionHanging On the Floor Cable Connections Changing the Wire Drive Ratio Wire Drive Gear Ratio High or LOW SpeedWork Cable Connections Selecting the Proper Gear Ratio Current Ratio Change Procedure Setting DIP Switches in the Control BOX DIP Switch Setup Figure A.4 Setting DIP Switches in the Wire Drive FAST-MATEGUN Adapter Guide Tubes Procedure to Install Drive Rolls and Guide TubesDrive Roll KIT and Guide Tube Installation Magnum Guns GUN and Cable AssembliesGUN Connection Guidelines General Guidelines Lifting Handle Gmaw Shielding GASCylinder may explode if damaged Buildup of Shielding GAS may harm health or kill Optional Panels for Control BOX General Panel Installation Guidelines Operation K1542-11 MX2 PanelOptional Control Box Panels Lower PanelsK1542-4 CV/Gouge PanelStd K1542-12 MSP2 Panel Optional K1640-1 Dual Procedure / Memory Door Panel Optional Control BOX -- PC Board Adjustments Control BOX Panels -- SET UP Controls Description Control BOX -- Setting Operating Limits Control BOX -- Using Operating Limits Wire Drive Settings -- External Wire Drive OperationSTEP/4 Step Switch Cold Feed / GAS Purge Switch Wire Drive -- PC Board Adjustments Wire Reel Loading READI-REELS, Spools or CoilsElectrode Polarity Gear BOX Ratio Drive Roll Pressure Setting Feeding Electrode and Brake AdjustmentGAS Guard Regulator Setting Making a Weld Wire Reel ChangingWire Feed Overload Protection Status Light States Component Status Lights Status Light States CON’T Wire Size Roll Drive Driven Solid Steel Electrode AccessoriesTable C.1 Drive Roll and Guide Tube Kits Cored Electrode K1543, K1544 and K1545 Input Cable Assemblies General Panel Installation GuidelinesDescription of Optional CON- Trol BOX Panels K1536-1 Water Flow Sensor KIT Wire Spindle AdaptersK659-1 GAS Guard Regulator K1649-1 Mounting Bracket Horizontal Maintenance MaintenanceWire Drive Motor and Gearbox Gun and Cable Maintenance HOW to USE Troubleshooting Guide 1TROUBLESHOOTINGE-1 Troubleshooting Your local Lincoln Authorized Possible Cause Recommended Symptoms Course of ActionField Service Facility Troubleshooting Course of Action Possible Cause Either of these fail, the problem is Change Or harness disconnected from Fails the continuity test, repair or Possible Cause Err 003 Err 001Err 004 Err 005 Err 100 Err 020Err 200 Err 201 Err 212 Err 211 Wiring Diagram Power Feed 11 Wire Feeder Wiring Diagram Diagrams L10834 Power Feed $700.00 Basic Course Precaucion Warnung