Fails the continuity test, repair or | Lincoln Electric IM613-B

E-8			TROUBLESHOOTING	E-8

		Observe all Safety Guidelines detailed throughout this manual
		PROBLEMS	POSSIBLE CAUSE	RECOMMENDED
		(SYMPTOMS)	POSSIBLE CAUSE	COURSE OF ACTION
		(SYMPTOMS)		COURSE OF ACTION

15.	Display(s) are blank.		a. Power source is OFF.
			b. Feeder supply or fuse circuit at
			power source is blown or tripped,
			or defective harness or cabling.
			c. Display or CB boards may be
			faulty.

16.	Dual Procedure is not function-		a. Gun has not been selected at the
	ing when using remote dual pro-		control box. Set dual procedure
	cedure switch. Status lights are		switch on CB to gun. Refer to
	solid green on CB and head		operating instructions.
	boards.		b. Faulty remote dual procedure	If all recommended possible areas of
			b. Faulty remote dual procedure	If all recommended possible areas of
			switch. Remove switch. Check	misadjustment have been checked
			continuity between switch pins	and the problem persists, Contact
			with switch open and closed. If it	your local Lincoln Authorized
			fails the continuity test, repair or	Field Service Facility.
			replace switch.
			c. Faulty Local Dual procedure
			switch.

CAUTION

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.

POWER FEED 11

Image 42

Lincoln Electric IM613-B manual Fails the continuity test, repair or

Contents

Safety Depends on You IM613-B Safety Electric Shock can kill Safety Iii Précautions DE Sûreté Sûreté Pour Soudage a L’Arc Thank You Table of Contents Section E Section FP315 Series Installation Power Feed Hanging Safety PrecautionWire Feeder to Power Source Configurations On the Floor Cable Connections Work Cable Connections Selecting the Proper Gear Ratio Wire Drive Gear Ratio High or LOW SpeedChanging the Wire Drive Ratio Current Ratio Change Procedure DIP Switch Setup Setting DIP Switches in the Control BOX Setting DIP Switches in the Wire Drive Figure A.4 Procedure to Install Drive Rolls and Guide Tubes Drive Roll KIT and Guide Tube InstallationFAST-MATEGUN Adapter Guide Tubes GUN Connection Guidelines GUN and Cable AssembliesMagnum Guns General Guidelines Cylinder may explode if damaged Gmaw Shielding GASLifting Handle Buildup of Shielding GAS may harm health or kill General Panel Installation Guidelines Optional Panels for Control BOX Operation Control Box Panels Lower Panels K1542-4 CV/Gouge PanelStdK1542-11 MX2 PanelOptional K1640-1 Dual Procedure / Memory Door Panel Optional K1542-12 MSP2 Panel Optional Control BOX Panels -- SET UP Controls Description Control BOX -- PC Board Adjustments Control BOX -- Using Operating Limits Control BOX -- Setting Operating Limits STEP/4 Step Switch Wire Drive OperationWire Drive Settings -- External Cold Feed / GAS Purge Switch Electrode Polarity Wire Reel Loading READI-REELS, Spools or CoilsWire Drive -- PC Board Adjustments Gear BOX Ratio Feeding Electrode and Brake Adjustment GAS Guard Regulator SettingDrive Roll Pressure Setting Wire Reel Changing Wire Feed Overload ProtectionMaking a Weld Component Status Lights Status Light States Status Light States CON’T Table C.1 Drive Roll and Guide Tube Kits AccessoriesWire Size Roll Drive Driven Solid Steel Electrode Cored Electrode General Panel Installation Guidelines Description of Optional CON- Trol BOX PanelsK1543, K1544 and K1545 Input Cable Assemblies K659-1 GAS Guard Regulator Wire Spindle AdaptersK1536-1 Water Flow Sensor KIT K1649-1 Mounting Bracket Horizontal Wire Drive Motor and Gearbox MaintenanceMaintenance Gun and Cable Maintenance 1TROUBLESHOOTINGE-1 HOW to USE Troubleshooting Guide Troubleshooting Possible Cause Recommended Symptoms Course of Action Field Service FacilityYour local Lincoln Authorized Troubleshooting Possible Cause Course of Action Either of these fail, the problem is Change Or harness disconnected from Fails the continuity test, repair or Possible Cause Err 004 Err 001Err 003 Err 005 Err 200 Err 020Err 100 Err 201 Err 211 Err 212 Wiring Diagram Power Feed 11 Wire Feeder Diagrams Wiring Diagram L10834 Power Feed Basic Course $700.00 Precaucion Warnung