Input Connections | Lincoln Electric 3200HD, IM759 specs

A-6	INSTALLATION	A-6

INPUT CONNECTIONS

Refer to Figure A.6.

The WELD-PAK 3200HD has a power input cable located on the rear of the machine.

GAS SOLENOID

INLET FITTING

POWER INPUT

CABLE

FIGURE A.6

CODE REQUIREMENTS FOR INPUT CONNECTIONS

WARNING

This welding machine must be connected to a power source in accordance with applicable elec- trical codes.

The United States National Electrical Code (Article 630-B, 1990 Edition) provides standards for amperage handling capability of supply conduc- tors based on duty cycle of the welding source.

If there is any question about the installation meeting applicable electrical code requirements, consult a qualified electrician.

Requirements For Rated Output

A power cord with a 15 amp, 125 volt, three prong plug (NEMA Type 5-15P) is factory installed on the WELD-PAK 3200HD. Connect this plug to a mating grounded receptacle which is connected to a 20 amp branch circuit with a nominal voltage rating of 115 to 125 volts, 60 Hertz, AC only.

The rated output with this installation is 90 amps,19 Volts, 20% duty cycle (2 minutes of every 10 minutes used for welding).

CAUTION

Do not connect the WELD-PAK 3200HD to an input power supply with a rated voltage that is greater than 125 volts.

Do not remove the power cord ground prong.

WELD-PAK 3200HD

Image 13

Lincoln Electric 3200HD, IM759 manual Code Requirements for Input Connections, Requirements For Rated Output

Contents

WELD-PAK 3200HD California Proposition 65 Warnings Safety Electric Shock can kill Iii Welding Sparks can cause fire or explosion Sûreté Pour Soudage a L’Arc Précautions DE Sûreté Please Examine Carton and Equipment For Damage Immediately Thank You Master Table of Contents for ALL Sections Technical Specifications WELD-PAK 3200HD Installation Identify and Locate Components Safety PrecautionsElectric Shock can kill Select Suitable Location Work Clamp InstallationOutput Connections Stacking Work Cable Installation GUN InstallationConnecting Gun Cable to the WELD-PAK GAS Connection Figure A.5 Code Requirements for Input Connections Input ConnectionsRequirements For Rated Output Figure A.7 WELD-PAK 3200HD Undercarriage Assembly Operation Design FeaturesGeneral Description Recommended Processes Welding Capability Controls and SettingsLimitations Welding Operations Wire LoadingSequence of Operation Wire Threading Friction Brake Adjustment Process Guidelines Cleaning Tip And NozzleMaking a Weld Welding with Gmaw MIG Changing Machine Over to Feed Other Wire SizesOverload Protection Learning to Weld Learning to WeldARC-WELDING Circuit SELF-SHIELDED Fcaw Welding ARC Process Selection Gmaw MIG Welding ARC Joint Types and Positions Common MetalsFor Gmaw MIG Process For Fcaw Innershield Process Penetration Welding In The Vertical PositionFillet Welds Welding Techniques for the SELF- Shielded Fcaw Process Machine SET UP for the SELF-SHIELDED Fcaw ProcessVertical-down Welding Correct Welding Position Correct Welding Speed Correct Electrical Stickout ESO Practice Helpful Hints Welding Techniques for the Gmaw MIG Process Machine SET UP for the Gmaw MIG Process For the WELD-PAK 3200HD, use the following To Eliminate a Ropy Convex Bead in order of importance Troubleshooting WeldsTo Correct Poor Penetration in order of impor- tance To Eliminate Stubbing* in order of importance Proper Gun Handling Application Chart Optional Accessories AccessoriesK586-1 Deluxe Adjustable Gas Regulator Hose Kit Replacement Parts Maintenance Safety Precautions MaintenanceRoutine Maintenance Configuration of Components in Wire Feeding System GUN and Cable MaintenanceFor Magnum 100L GUN Contact Tip Cable Liner Drive Roll Changing the Contact TIP Component Replacement ProceduresChanging Drive Roll GUN Handle Parts Changing LinerLiner trim length HOW to USE Troubleshooting Guide Troubleshooting Recommended Course of Action Problems Possible Areas Symptoms Misadjustments Facility Contact your local Lincoln Authorized Field Service Welding Problems WELD-PAK 3200HD Wiring Diagram Diagrams WELD-PAK 3200HD New Lessons in Arc Welding How To Read Shop DrawingsNeed Welding Training? $700.00 Precaucion Warnung