Component Replacement Procedures | Lincoln Electric 3200HD, IM759

D-3	MAINTENANCE	D-3

COMPONENT

REPLACEMENT

PROCEDURES

CHANGING THE CONTACT TIP

1.Refer to Figure D.2. Remove the gas nozzle from the gun by unscrewing counter-clockwise.

2.Remove the existing contact tip from the gun by unscrewing counter-clockwise.

3.Insert and hand tighten desired contact tip.

4.Replace gas nozzle.

CHANGING DRIVE ROLL

The drive roll has two grooves; one for .023" – .025" (0.6 mm) solid steel electrode and a larger knurled groove for .030" (0.8 mm) solid and .035" (0.9 mm) flux-cored steel electrode. As shipped, the drive roll is installed in the .030"/.035" (0.8/0.9 mm) position.

If .023" – .025" (0.6 mm) wire is to be used, the drive roll must be reversed as follows:

1.Connect the machine to its rated input power per instructions in Installation section.

2.Release the spring-loaded idle arm tensioner Item 2, and lift the idle roll arm, Item 3, away from the drive roll, Item 1. (See Figure D.1)

3.Turn the power switch to ON (marked “I”).

4.Set the wire speed to minimum and jog the drive unit with the trigger switch until the drive roll set screw is facing up.

CAUTION

When inching the welding wire, the drive rolls, gun connector block, and gun contact tip are energized relative to work and ground and remain energized for several seconds after the gun trig- ger is released.

5.Turn the power switch to OFF (marked “O”).

6.Loosen the drive roll set screw with the 5/64" (2.0 mm) hex wrench supplied.

7.Remove the drive roll, flip over and reinstall with the

.023 – .025" (0.6 mm) groove (the smaller groove) closest to the gearbox.

8.Push a length of straightened welding wire through the wire feeder guide tubes and adjust the position of the drive roll so that the groove is centered on the wire. Make certain the set screw is located on the flat portion of the shaft and tighten.

FIGURE D.1

3

2

1

WELD-PAK 3200HD

Image 37

Lincoln Electric 3200HD, IM759 manual Component Replacement Procedures, Changing the Contact TIP, Changing Drive Roll

Contents

WELD-PAK 3200HD California Proposition 65 Warnings Safety Electric Shock can kill Iii Welding Sparks can cause fire or explosion Sûreté Pour Soudage a L’Arc Précautions DE Sûreté Please Examine Carton and Equipment For Damage Immediately Thank You Master Table of Contents for ALL Sections Technical Specifications WELD-PAK 3200HD Installation Identify and Locate Components Safety PrecautionsElectric Shock can kill Select Suitable Location Work Clamp InstallationOutput Connections Stacking Work Cable Installation GUN InstallationConnecting Gun Cable to the WELD-PAK GAS Connection Figure A.5 Code Requirements for Input Connections Input ConnectionsRequirements For Rated Output Figure A.7 WELD-PAK 3200HD Undercarriage Assembly Operation Design FeaturesGeneral Description Recommended Processes Welding Capability Controls and SettingsLimitations Welding Operations Wire LoadingSequence of Operation Wire Threading Friction Brake Adjustment Process Guidelines Cleaning Tip And NozzleMaking a Weld Welding with Gmaw MIG Changing Machine Over to Feed Other Wire SizesOverload Protection Learning to Weld Learning to WeldARC-WELDING Circuit SELF-SHIELDED Fcaw Welding ARC Process Selection Gmaw MIG Welding ARC Joint Types and Positions Common MetalsFor Gmaw MIG Process For Fcaw Innershield Process Penetration Welding In The Vertical PositionFillet Welds Welding Techniques for the SELF- Shielded Fcaw Process Machine SET UP for the SELF-SHIELDED Fcaw ProcessVertical-down Welding Correct Welding Position Correct Welding Speed Correct Electrical Stickout ESO Practice Helpful Hints Welding Techniques for the Gmaw MIG Process Machine SET UP for the Gmaw MIG Process For the WELD-PAK 3200HD, use the following To Eliminate a Ropy Convex Bead in order of importance Troubleshooting WeldsTo Correct Poor Penetration in order of impor- tance To Eliminate Stubbing* in order of importance Proper Gun Handling Application Chart Optional Accessories AccessoriesK586-1 Deluxe Adjustable Gas Regulator Hose Kit Replacement Parts Maintenance Safety Precautions MaintenanceRoutine Maintenance Configuration of Components in Wire Feeding System GUN and Cable MaintenanceFor Magnum 100L GUN Contact Tip Cable Liner Drive Roll Changing the Contact TIP Component Replacement ProceduresChanging Drive Roll GUN Handle Parts Changing LinerLiner trim length HOW to USE Troubleshooting Guide Troubleshooting Recommended Course of Action Problems Possible Areas Symptoms Misadjustments Facility Contact your local Lincoln Authorized Field Service Welding Problems WELD-PAK 3200HD Wiring Diagram Diagrams WELD-PAK 3200HD New Lessons in Arc Welding How To Read Shop DrawingsNeed Welding Training? $700.00 Precaucion Warnung