|
| OPERATION | |||
|
|
|
|
|
|
|
| WELD SEQUENCE PARAMETER LIST |
| ||
|
|
|
|
| |
PARAMETER | UNITS | RANGE | DEFAULT VALUE | WHERE IS IT SET? | |
|
|
|
|
| |
Arc Delay Time | seconds | OFF | MSP4 - START OPTIONS | ||
|
|
|
|
| |
Strike Fault Time | seconds | OFF | MSP4- SETUP Menu | ||
|
|
|
|
|
|
| Strike WFS | IPM | from weld table* | weld mode dependant | Left Dual Display |
|
|
|
|
|
|
| Strike Volts | volts | from weld table* | weld mode dependant | Right Dual Display |
|
|
|
|
|
|
| Restrike Time | seconds | OFF | MSP4 - SETUP Menu | |
|
|
|
|
| |
Start WFS/Amps | IPM/amperes | from weld table* | weld mode dependant | Left Dual Display | |
|
|
|
|
|
|
| Start Volts | volts | from weld table* | weld mode dependant | Right Dual Display |
|
|
|
|
|
|
| Start Time | seconds | 0.1 | MSP4 - START OPTIONS | |
|
|
|
|
| |
Start Arc Force | amperes | from weld table* | weld mode dependant | MSP4 - SETUP Menu | |
|
|
|
|
|
|
| Upslope Time | seconds | OFF | MSP4 - SETUP Menu | |
|
|
|
|
| |
Weld WFS/Amps | IPM/amperes | from weld table* | weld mode dependant | Left Dual Display | |
|
|
|
|
|
|
| Weld Volts | volts | from weld table* | weld mode dependant | Right Dual Display |
|
|
|
|
| |
Weld Arc Force | amperes | from weld table* | weld mode dependant | MSP4 - SETUP Menu | |
|
|
|
|
| |
Frequency (AC) | hertz | weld mode dependant | AC CONTROL | ||
|
|
|
|
|
|
| Balance (AC) | percent | weld mode dependant | AC CONTROL | |
|
|
|
|
|
|
| Offset (AC) | percent | 0.0 | AC CONTROL | |
|
|
|
|
| |
Arc 2 Phase (if applicable) | degrees | 90 | AC CONTROL | ||
|
|
|
|
| |
Arc 2 Balance (if applicable) | percent | 50 | AC CONTROL | ||
|
|
|
|
| |
Arc 3 Phase (if applicable) | degrees | 180 | AC CONTROL | ||
|
|
|
|
| |
Arc 3 Balance (if applicable) | percent | 50 | AC CONTROL | ||
|
|
|
|
| |
Arc 4 Phase (if applicable) | degrees | 270 | AC CONTROL | ||
|
|
|
|
| |
Arc 4 Balance (if applicable) | percent | 50 | AC CONTROL | ||
|
|
|
|
| |
Downslope Time | seconds | OFF | MSP4 - SETUP Menu | ||
|
|
|
|
| |
Crater WFS/Amps | IPM/amperes | from weld table* | weld mode dependant | Left Dual Display | |
|
|
|
|
|
|
| Crater Volts | volts | from weld table* | weld mode dependant | Right Dual Display |
|
|
|
|
|
|
| Crater Time | seconds | OFF | END OPTIONS | |
|
|
|
|
| |
Crater Arc Force | amperes | from weld table* | weld mode dependant | MSP4 - SETUP Menu | |
|
|
|
|
| |
Burnback Time | seconds | 0.2 | END OPTIONS | ||
|
|
|
|
|
|
* Range depends on the Machine Power Source, Literature and Tables supplied with each unit.
