Wireless Wireless Connection Control Tab | Linksys WAP200RF manual

Wireless-G Access Point with Power Over Ethernet and Rangebooster

The Wireless - Wireless Connection Control Tab

This screen allows you to configure the Connection Control List to either permit or block specific wireless client devices connecting to (associating with) the Access Point.

Wireless Connection Control

Select SSID. Select the SSID of the wireless network that you want to use wireless connection control on.

Enabled/Disabled. Enable or disable wireless connection control. The default is disabled.

Connection Control

Allow only following MAC addresses to connect to wireless network. When this option is selected, only devices with a MAC address specified in the Connection Control List can connect to the Access Point.

Prevent following MAC addresses from connecting to wireless network. When this option is selected, devices with a MAC address specified in the Connection Control List will not be allowed to connect to the Access

Point.	Figure 6-13: Wireless - Wireless Connection Control

Wireless Client List

Instead of manually entering the MAC addresses of each client, the Access Point provides a convenient way to select a specific client device from the client association table. Click this button and a window appears to let you select a MAC address from the table. The selected MAC address will be entered into the Connection Control List.

Connection Control List

MAC 01-16. Enter the MAC addresses of the wireless client devices you want to control.
Change these settings as described here and click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes. Help information is available on the right side of the screen.	Figure 6-14: Select MAC Address from Wireless Client List

Chapter 6: Configuring the Wireless-G Access Point

24

The Wireless - Wireless Connection Control Tab

Image 30

Linksys WAP200RF manual Wireless Wireless Connection Control Tab, Wireless Client List, Connection Control List

Contents

User Guide How to Use this User Guide Copyright and Trademarks Table of Contents Appendix a Troubleshooting Appendix B Wireless SecurityFrequently Asked Questions Example of a Simple Wireless Network List of Figures 20 Security Monitor Basic Settings Introduction Welcome What’s in this User Guide? Introduction What’s in this User Guide? Planning Your Wireless Network Network TopologyRoaming Network Layout Example of a simple wireless network Getting to Know the Wireless-G Access Point LEDs Access Point’s port are located on the back of the device Ports Desktop Placement and Antenna Setup Antennas and Positions Connecting the Wireless-G Access Point OverviewConnection Placement Options Stand OptionWall-Mount Option Setting Up the Wireless-G Access Point Accessing the Utility Setup WirelessNavigating the Utility AP Mode AdministrationSecurity Monitor Status Basic Setup Configuring the Wireless-G Access PointSetup Basic Setup Tab Network Setup Setup Time Tab Time Wireless Basic Wireless Settings Tab Basic Settings Wireless Wireless Security Tab Wireless Security WPA-Personal aka WPA-PSK WPA2-Personal WPA2-Personal Mixed WPA-Enterprise WPA2-Enterprise WPA2-Enterprise Mixed Disable Radius Wireless Client List Wireless Wireless Connection Control TabWireless Connection Control Connection Control Wireless Advanced Wireless Settings Tab Advanced Settings Wireless Vlan & QoS Tab Vlan QoS AP Mode Tab MAC Address 18 Wireless Repeater Mode 19 Wireless Bridge Mode Security Monitor Basic Settings Tab Wireless Security MonitorSecurity Monitor Accounts Security Monitor Event Log Tab Mail Notification Syslog Notification Local AP Password Administration Management TabWeb Access Management Snmp Identification Email Alert Administration Log TabLog Notification Queue Length Factory Default Administration Factory Default TabAdministration Firmware Upgrade Tab Firmware Upgrade Reboot Administration Reboot TabAdministration Config Management Tab Config Management Status Local Network Tab InformationLocal Network Status Wireless Tab Wireless Network Status System Performance Tab WiredWireless System PerformancePage Appendix a Troubleshooting Frequently Asked Questions What Ieee 802.11g features are supported? What is the ISM band? Does the Access Point function as a firewall? Appendix B Wireless Security Security PrecautionsSecurity Threats Facing Wireless Networks Appendix B Wireless Security Page Appendix C Upgrading Firmware Appendix D Windows Help Shared ResourcesNetwork Neighborhood/My Network Places Appendix E Glossary Appendix E Glossary Appendix E Glossary Appendix E Glossary Appendix E Glossary Appendix F Specifications 802.11F Wireless Roaming 11.g 54Mbps@ -72dBm, 11.b 11Mbps@ -85dBM Dhcp Client11g 14 dBm Security Wireless Security Monitor Suspicious network eventsCertification Appendix G Warranty Information Limited Warranty Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix I Contact Information Need to contact Linksys?Information section in this Guide