Syslog Notification | Linksys WAP200RF guide

Wireless-G Access Point with Power Over Ethernet and Rangebooster

• Duplicate SSID in use. Indicates an unauthorized AP has the same SSID value as an authorized AP.

SYSLOG Notification

Logviewer IP Address. Enter the IP address of the system that will store the system log.

Alarm Type. Select the type of intrusions that should require an e-mail notification.

•Rogue AP Detected. Indicates a rogue access point has been detected.

•AP SSID Changed. Indicates the Access Point’s SSID has been changed.

•Spoofed MAC Address. Indicates another device is using the AP’s MAC address to send out packets.

•Client is Sending Spurious Traffic. Indicates an unassociated client is sending out frames to the AP.

•Adhoc SSID same as AP. Indicates an Adhoc network uses the same SSID as the AP.

•Adhoc Network Operating. Indicates when a STA is advertising a peer-to-peer (Adhoc) network.

•Rogue Client Detected. Indicates when a STA is conducting an illegal transaction with an AP.

•Default SSID in use. Indicates when the default SSID is in use on an AP.

•Association Table Full. Indicates an AP refused a new STA association due to resource unavailability.

•Low Speed Connection. Indicates when a STA is transmitting data at a much slower rate set by AP.

•New Client Detected. Indicates a new STA is associated with an AP.

•New Access Point Detected. Indicates a new AP has been detected joining the network.

•Duration Attack. Indicates a STA packet contains an abnormally large duration value in the 802.11 header.

•AP is Not Using Encryption. Indicates when an AP has wireless security disabled.

•AP Channel Changed. Indicates when an AP changes its wireless channel.

•AP Broadcasting SSID. Indicates when SSID broadcasting is enabled on an AP.

•Duplicate SSID in use. Indicates an unauthorized AP has the same SSID value as an authorized AP.

Chapter 6: Configuring the Wireless-G Access Point

33

The Security Monitor - Event Log Tab

Image 39

Linksys WAP200RF manual Syslog Notification

Contents

User Guide Copyright and Trademarks How to Use this User Guide Table of Contents Appendix a Troubleshooting Appendix B Wireless SecurityFrequently Asked Questions List of Figures Example of a Simple Wireless Network 20 Security Monitor Basic Settings Welcome Introduction What’s in this User Guide? Introduction What’s in this User Guide? Planning Your Wireless Network Network TopologyRoaming Network Layout Example of a simple wireless network LEDs Getting to Know the Wireless-G Access Point Ports Access Point’s port are located on the back of the device Antennas and Positions Desktop Placement and Antenna Setup Connecting the Wireless-G Access Point OverviewConnection Placement Options Stand OptionWall-Mount Option Accessing the Utility Setting Up the Wireless-G Access Point Setup WirelessNavigating the Utility AP Mode AdministrationSecurity Monitor Status Network Setup Configuring the Wireless-G Access PointSetup Basic Setup Tab Basic Setup Time Setup Time Tab Basic Settings Wireless Basic Wireless Settings Tab Wireless Security Wireless Wireless Security Tab WPA2-Personal WPA-Personal aka WPA-PSK WPA-Enterprise WPA2-Personal Mixed WPA2-Enterprise Mixed WPA2-Enterprise Radius Disable Connection Control Wireless Wireless Connection Control TabWireless Connection Control Wireless Client List Advanced Settings Wireless Advanced Wireless Settings Tab Vlan Wireless Vlan & QoS Tab QoS MAC Address AP Mode Tab 18 Wireless Repeater Mode 19 Wireless Bridge Mode Security Monitor Basic Settings Tab Wireless Security MonitorSecurity Monitor Accounts Mail Notification Security Monitor Event Log Tab Syslog Notification Management Administration Management TabWeb Access Local AP Password Identification Snmp Notification Queue Length Administration Log TabLog Email Alert Firmware Upgrade Administration Factory Default TabAdministration Firmware Upgrade Tab Factory Default Config Management Administration Reboot TabAdministration Config Management Tab Reboot Status Local Network Tab InformationLocal Network Wireless Network Status Wireless Tab System Performance WiredWireless Status System Performance TabPage Frequently Asked Questions Appendix a Troubleshooting What Ieee 802.11g features are supported? What is the ISM band? Does the Access Point function as a firewall? Appendix B Wireless Security Security PrecautionsSecurity Threats Facing Wireless Networks Appendix B Wireless Security Page Appendix C Upgrading Firmware Appendix D Windows Help Shared ResourcesNetwork Neighborhood/My Network Places Appendix E Glossary Appendix E Glossary Appendix E Glossary Appendix E Glossary Appendix E Glossary 802.11F Wireless Roaming Appendix F Specifications Security Dhcp Client11g 14 dBm 11.g 54Mbps@ -72dBm, 11.b 11Mbps@ -85dBM Wireless Security Monitor Suspicious network eventsCertification Limited Warranty Appendix G Warranty Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix I Contact Information Need to contact Linksys?Information section in this Guide