Manuals / Linksys / Computer Equipment / Network Card

Linksys WAP200RF manual Administration Factory Default Tab, Administration Firmware Upgrade Tab

Models: WAP200RF WAP200

1 74

Download 74 pages 50.69 Kb

Page 43

Wireless-G Access Point with Power Over Ethernet and Rangebooster

System Error Messages. If you want to log system error messages, click the checkbox.

Configuration Changes. If you want to log any configuration changes, click the checkbox.

Change these settings as described here and click Save Settings to apply your changes, or click Cancel Changes to cancel your changes. Help information is available on the right side of the screen.

The Administration - Factory Default Tab

On this screen you can restore the Access Point’s factory default settings.

Factory Default

Note any custom settings before you restore the factory defaults. Once the Access Point is reset, you will have to re-enter all of your configuration settings.

Restore Factory Defaults. To restore the Access Point's factory default settings, click the Yes radio button. Then, click Save Settings. Your Access Point will reboot and come back up with the factory default settings in a few seconds.

Click Save Settings to apply your change, or click Cancel Changes to cancel your change. Help information is available on the right side of the screen.

The Administration - Firmware Upgrade Tab

On this screen you can upgrade the Access Point’s firmware. Do not upgrade the firmware unless you are experiencing problems with the Access Point or the new firmware has a feature you want to use.

Firmware Upgrade

Before you upgrade the Access Point’s firmware, note all of your custom settings. After you upgrade its firmware, you will have to re-enter all of your configuration settings. To upgrade the Access Point’s firmware:

1.Download the firmware upgrade file from the Linksys website, www.linksys.com.

2.Extract the firmware upgrade file on your computer.

Chapter 6: Configuring the Wireless-G Access Point

Figure 6-24: Administration - Factory Default

Figure 6-25: Administration - Firmware Upgrade

37

The Administration - Factory Default Tab

Image 43

Linksys WAP200RF manual Administration Factory Default Tab, Administration Firmware Upgrade Tab

Contents

User Guide Copyright and Trademarks How to Use this User GuideTable of Contents Appendix B Wireless Security Appendix a TroubleshootingFrequently Asked Questions List of Figures Example of a Simple Wireless Network20 Security Monitor Basic Settings Welcome IntroductionWhat’s in this User Guide? Introduction What’s in this User Guide? Network Topology Planning Your Wireless NetworkRoaming Network Layout Example of a simple wireless network LEDs Getting to Know the Wireless-G Access PointPorts Access Point’s port are located on the back of the deviceAntennas and Positions Desktop Placement and Antenna SetupOverview Connecting the Wireless-G Access PointConnection Stand Option Placement OptionsWall-Mount Option Accessing the Utility Setting Up the Wireless-G Access PointWireless SetupNavigating the Utility Administration AP ModeSecurity Monitor Status Network Setup Configuring the Wireless-G Access PointSetup Basic Setup Tab Basic SetupTime Setup Time TabBasic Settings Wireless Basic Wireless Settings TabWireless Security Wireless Wireless Security TabWPA2-Personal WPA-Personal aka WPA-PSKWPA-Enterprise WPA2-Personal MixedWPA2-Enterprise Mixed WPA2-EnterpriseRadius DisableConnection Control Wireless Wireless Connection Control TabWireless Connection Control Wireless Client ListAdvanced Settings Wireless Advanced Wireless Settings TabVlan Wireless Vlan & QoS TabQoS MAC Address AP Mode Tab18 Wireless Repeater Mode 19 Wireless Bridge Mode Wireless Security Monitor Security Monitor Basic Settings TabSecurity Monitor Accounts Mail Notification Security Monitor Event Log TabSyslog Notification Management Administration Management TabWeb Access Local AP PasswordIdentification SnmpNotification Queue Length Administration Log TabLog Email AlertFirmware Upgrade Administration Factory Default TabAdministration Firmware Upgrade Tab Factory DefaultConfig Management Administration Reboot TabAdministration Config Management Tab RebootInformation Status Local Network TabLocal Network Wireless Network Status Wireless TabSystem Performance WiredWireless Status System Performance TabPage Frequently Asked Questions Appendix a TroubleshootingWhat Ieee 802.11g features are supported? What is the ISM band? Does the Access Point function as a firewall? Security Precautions Appendix B Wireless SecuritySecurity Threats Facing Wireless Networks Appendix B Wireless Security Page Appendix C Upgrading Firmware Shared Resources Appendix D Windows HelpNetwork Neighborhood/My Network Places Appendix E Glossary Appendix E Glossary Appendix E Glossary Appendix E Glossary Appendix E Glossary 802.11F Wireless Roaming Appendix F SpecificationsSecurity Dhcp Client11g 14 dBm 11.g 54Mbps@ -72dBm, 11.b 11Mbps@ -85dBMSuspicious network events Wireless Security MonitorCertification Limited Warranty Appendix G Warranty InformationAppendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Need to contact Linksys? Appendix I Contact InformationInformation section in this Guide