Does the Access Point function as a firewall? | Linksys WAP200

Wireless-G Access Point with Power Over Ethernet and Rangebooster

What is a MAC Address?

The Media Access Control (MAC) address is a unique number assigned by the manufacturer to any Ethernet networking device, such as a network adapter, that allows the network to identify it at the hardware level. For all practical purposes, this number is usually permanent. Unlike IP addresses, which can change every time a computer logs on to the network, the MAC address of a device stays the same, making it a valuable identifier for the network.

How do I avoid interference?

Using multiple Access Points on the same channel and in close proximity to one another will generate interference. When employing multiple Access Points, make sure to operate each one on a different channel (frequency).

How do I reset the Access Point?

Press the Reset button on the back of the Access Point for about ten seconds. This will reset the unit to its default settings.

How do I resolve issues with signal loss?

There is no way to know the exact range of your wireless network without testing. Every obstacle placed between an Access Point and wireless PC will create signal loss. Leaded glass, metal, concrete floors, water, and walls will inhibit the signal and reduce range. Start with your Access Point and your wireless PC in the same room and move it away in small increments to determine the maximum range in your environment.

You may also try using different channels, as this may eliminate interference affecting only one channel. Also, open the Access Point’s web-based utility. Click the Wireless tab and then the Advanced Wireless tab. Make sure the Output Power is set to 100%.

Does the Access Point function as a firewall?

No. The Access Point is only a bridge from wired Ethernet to wireless clients.

I have excellent signal strength, but I cannot see my network.

Wireless security, such as WEP or WPA, is probably enabled on the Access Point, but not on your wireless adapter (or vice versa). Verify that the same wireless security settings are being used on all devices in your wireless network.

What is the maximum number of users the Access Point can handle?

No more than 45, but this depends on the volume of data and may be fewer if many users create a large amount of network traffic.

Appendix A: Troubleshooting

46

Frequently Asked Questions

Image 52

Linksys WAP200RF manual Does the Access Point function as a firewall?

Contents

User Guide How to Use this User Guide Copyright and Trademarks Table of Contents Appendix B Wireless Security Appendix a TroubleshootingFrequently Asked Questions Example of a Simple Wireless Network List of Figures 20 Security Monitor Basic Settings Introduction Welcome What’s in this User Guide? Introduction What’s in this User Guide? Network Topology Planning Your Wireless NetworkRoaming Network Layout Example of a simple wireless network Getting to Know the Wireless-G Access Point LEDs Access Point’s port are located on the back of the device Ports Desktop Placement and Antenna Setup Antennas and Positions Overview Connecting the Wireless-G Access PointConnection Stand Option Placement OptionsWall-Mount Option Setting Up the Wireless-G Access Point Accessing the Utility Wireless SetupNavigating the Utility Administration AP ModeSecurity Monitor Status Configuring the Wireless-G Access Point Setup Basic Setup TabBasic Setup Network Setup Setup Time Tab Time Wireless Basic Wireless Settings Tab Basic Settings Wireless Wireless Security Tab Wireless Security WPA-Personal aka WPA-PSK WPA2-Personal WPA2-Personal Mixed WPA-Enterprise WPA2-Enterprise WPA2-Enterprise Mixed Disable Radius Wireless Wireless Connection Control Tab Wireless Connection ControlWireless Client List Connection Control Wireless Advanced Wireless Settings Tab Advanced Settings Wireless Vlan & QoS Tab Vlan QoS AP Mode Tab MAC Address 18 Wireless Repeater Mode 19 Wireless Bridge Mode Wireless Security Monitor Security Monitor Basic Settings TabSecurity Monitor Accounts Security Monitor Event Log Tab Mail Notification Syslog Notification Administration Management Tab Web AccessLocal AP Password Management Snmp Identification Administration Log Tab LogEmail Alert Notification Queue Length Administration Factory Default Tab Administration Firmware Upgrade TabFactory Default Firmware Upgrade Administration Reboot Tab Administration Config Management TabReboot Config Management Information Status Local Network TabLocal Network Status Wireless Tab Wireless Network Wired WirelessStatus System Performance Tab System PerformancePage Appendix a Troubleshooting Frequently Asked Questions What Ieee 802.11g features are supported? What is the ISM band? Does the Access Point function as a firewall? Security Precautions Appendix B Wireless SecuritySecurity Threats Facing Wireless Networks Appendix B Wireless Security Page Appendix C Upgrading Firmware Shared Resources Appendix D Windows HelpNetwork Neighborhood/My Network Places Appendix E Glossary Appendix E Glossary Appendix E Glossary Appendix E Glossary Appendix E Glossary Appendix F Specifications 802.11F Wireless Roaming Dhcp Client 11g 14 dBm11.g 54Mbps@ -72dBm, 11.b 11Mbps@ -85dBM Security Suspicious network events Wireless Security MonitorCertification Appendix G Warranty Information Limited Warranty Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Appendix H Regulatory Information Need to contact Linksys? Appendix I Contact InformationInformation section in this Guide