Marantz MV8300_U1B manual Input receiving channel number, Check program data

FUNCTION SET UP TUNER SET UP

INITIAL SET UP

EN 35

4Input receiving channel number

The guide channel

number, which is	CLOCK SET		GUIDE CHANNEL	OTHER
assigned to the TV or		GUIDE CH	12
		VCR CH	– –
cable station for the
PlusCode number
that you entered in	MENU	OK	SELECT WITH ARROW KEYS
step 3, will appear	EXIT	SELECT	THEN PRESS [OK]

automatically on the

Guide Channel Set Up screen.

Press @ # to input the number of the channel on which the broadcast for the PlusCode number is received on the VCR or cable box, then press OK.

●The Guide Channel Set screen appears only when you input the PlusCode number of a station for which the guide channel number has not been set previously.

●If you receive your channels with a cable box and if you have properly set your Controller, “CABLE CH” appears in place of “VCR CH”. If not, refer to pages 15 – 17.

In that case, it is possible to change the channel by 10 channels by pressing and holding @ #.

5Check program data

The PlusCode	TIMER PROGRAM
number you entered	PLUSCODE NO. 12345
	START TIME	STOP TIME	DATE	CH
and the
	8:00 PM	10:00 PM	12/24/03(WED)	12 CH
corresponding timer		REC SPEED	DAILY/WEEKLY	SOURCE
recording program is		STD (SP)	EVERY WED	CATV
	CONFIRM	CANCEL
displayed on the
	PROG.	SET PROGRAM WITH [+/–, REC SPEED,
Program screen.		8=DAILY, 9=WEEKLY] THEN PRESS "CONFIRM"
	EXIT START STOP DATE CH
Check to make sure it
is accurate.

●To change the start/stop time, date or channel setting, press the corresponding buttons to change the settings; START +/–, STOP +/–, DATE +/–, TV/VCR CH +/–.

●To timer-record daily or weekly serials, press DAILY (number “8”) or WEEKLY (number “9”). “MON – FRI”, “MON – SAT”, “SUN – SAT” or “EVERY _ _ _” appears on the Program screen. Pressing the button again makes each corresponding display disappear.

●For the “SOURCE” setting, refer to page 39.

●If you made a mistake, press BACK to access the VCR Plus+ screen again and input the correct PlusCode number.

6 Set recording speed

Press REC SPEED to set the recording speed.

7Return to normal screen

Press @ # to move the arrow to “CONFIRM”, then press OK.

“PROGRAM COMPLETED PRESS [TIMER] TO ENTER TIMER STANDBY MODE” appears on the screen, then press OK to return to normal screen.

8Engage timer recording standby mode

Press TIMER (‰).

The VCR turns off automatically and “‰” is displayed on the front display panel.

To use the VCR while it is in timer recording standby mode

Press TIMER (‰) to cancel the timer recording standby mode, then press POWER to turn on the VCR.

DO NOT forget to put the VCR into timer recording standby mode again by pressing TIMER (‰) after you use the VCR; otherwise, you cannot record the broadcasts you want.

●When “AUTO TIMER” ( pg. 57) is set to “ON”, the timer recording standby mode is automatically engaged when the VCR is turned off. It is temporarily canceled when the VCR is turned on. You do not have to press TIMER (‰) to engage or disengage the timer recording standby mode.

IMPORTANT

If you have moved to a different area or if a broadcasting station’s channel number has been changed, the wrong VCR CH or CABLE CH number will be displayed on the Program screen in step 5. When this happens, set the correct guide channel number for that station. ( pg. 36, “Changing VCR Plus+ Setting”)

NOTES:

●Even if a power failure occurs, the VCR keeps your timer programs. However, the clock time is lost if it lasts for more than 10 minutes.

As a result, when the power is supplied again to this VCR after the power failure, the following will take place.

1.This VCR starts Auto Clock Set automatically to restore the clock time.

2.If the clock time is restored correctly and “AUTO TIMER” is set to “ON”, each timer program you have made will start at its start time unless its end time has elapsed.

●If the tape reaches its end during timer recording, “‰”, “”, and “ #” blink.

●To timer-record cable channels received through a cable box, be sure to keep the cable box turned on.

HM-DH40000U-EN34-41 35 1/28/3, 10:07 AM