Marantz MV8300_U1B manual To timer-record daily or weekly serials, Catv, Dbs

PROG.

EXIT START STOP DATE CH

SET PROGRAM WITH [+/–, REC SPEED,7=DBS,

8=DAILY, 9=WEEKLY] THEN PRESS "CONFIRM"

EN 39

8 Set recording speed

Press REC SPEED to set the recording speed.

9 Return to normal screen

Press @ # to move the arrow to “CONFIRM”, then press OK.

“PROGRAM COMPLETED PRESS [TIMER] TO ENTER TIMER STANDBY MODE” appears on the screen, then press OK to return to normal screen.

0Engage timer recording standby mode

Press TIMER (‰).

The VCR turns off automatically and “‰” is displayed on the front display panel.

To timer-record daily or weekly serials

Press DAILY (number “8”) or WEEKLY (number “9”) anytime during steps 4 through 8.

“MON – FRI”, “MON – SAT”, “SUN – SAT” or “EVERY _ _ _” appears on the Program screen.

●Pressing the button again makes the corresponding indication disappear.

To use the VCR while it is in timer recording standby mode

Press TIMER (‰) to cancel the timer recording standby mode, then press POWER to turn on the VCR.

DO NOT forget to put the VCR into timer recording standby mode again by pressing TIMER (‰) after you use the VCR; otherwise, you cannot record the broadcast you want.

●When “AUTO TIMER” ( pg. 57) is set to “ON”, the timer recording standby mode is automatically engaged when the VCR is turned off. It is temporarily canceled when the VCR is turned on. You do not have to press TIMER (‰) to engage or disengage the timer recording standby mode.

NOTES:

●Even if a power failure occurs, the VCR keeps your timer programs. However, the clock time is lost if it lasts for more than 10 minutes.

As a result, when the power is supplied again to this VCR after the power failure, the following will take place.

1.This VCR starts Auto Clock Set automatically to restore the clock time.

2.If the clock time is restored correctly and “AUTO TIMER” is set to “ON”, each timer program you have made will start at its start time unless its end time has elapsed.

●Programs that start after midnight must have the next day’s date.

●After timer recording is completed, the VCR turns off automatically.

●You can program the timer recording while a regular recording is in progress; the menu screens will not be recorded.

●If the tape reaches its end during timer recording, “‰”, “”, and “ #” blink.

●To timer-record cable or satellite channels, be sure to keep the cable box or DBS receiver turned on.

ATTENTION FOR DBS RECEIVER USERS

If you are using a DBS	TIMER PROGRAM
receiver (unless “INPUT
	START TIME	STOP TIME	DATE	CH
CH” is set to “OFF” on
	8:00 PM	10:00 PM	12/24/03(WED)	110 CH
DBS Receiver Set screen		REC SPEED	DAILY/WEEKLY	SOURCE
		STD (SP)	EVERY WED	DBS
 pg. 19), the band
	CONFIRM	CANCEL

indication (TV, CATV or DBS) appears under the channel number indication (SOURCE).

TV	:To timer-record a regular TV broadcast
	received on the VCR.
CATV	:To timer-record a cable TV broadcast
	received on the VCR, or through a cable box
	(unless “INPUT CH” is set to “OFF” on
	Cable Set Up screen  pg. 16).
DBS	:To timer-record a satellite broadcast
	received through a DBS receiver.

NOTE:

If “BAND” is set to “TV” on the Tuner Set Up Screen

( pg. 14) and “INPUT CH” is set to “OFF” on Cable Set Up screen ( pg. 16), “CATV” will not be displayed on the Program screen; If “BAND” is set to “CATV” or “INPUT CH” is set to “ON” on Cable Set Up screen, “TV” will not be displayed.

If the channel number entered requires that the band be set, “7=DBS” is displayed on the screen.

If this happens, press the Number key “7 (DBS)” to select “DBS”.

HM-DH40000U-EN34-41 39 1/28/3, 10:07 AM