REMOTE CONTROLLER

RC7300SRa

NAMES AND FUNCTIONS

z

xS

c‹4

v b

‹3

n

‹2

m

‹1

 

‹0

,

¤9

 

 

¤8

.

¤7

¤6

⁄0

¤5

⁄1

¤4

⁄2

¤3

⁄3 ¤2 ⁄4

⁄5

⁄6¤1

⁄7¤0

⁄8

⁄9

zInfrared window

Outputs and inputs-, infrared control signals.

xLCD (Liquid Crystal Display)

Used to display information about currently selected functions.

c/ (open/close) button Used to open or close the door.

Note:

This button is unavailable for the SR6400. v Source POWER ON/OFF button

Used to turn specific sources (such as DVD players, etc.) ON and OFF independently from the rest of the system.

bEQ button

Used to turn on or off HT (Home Theater)-EQ mode. This mode compensates for the audio portion of a movie sounding “bright”. When this button is pressed, “EQ” indicator is illuminated.

nV-OFF (video off) button Used to turn off the video signal.

mDVD operating buttons

(when DVD mode is selected)

AUDIO button

Used to select one of the audio languages.

ANGLE button

Used to change the different camera angles.

SUBTITLE button

Used to select one of the subtitle languages.

,Numeric buttons 1 to 9, 0 / Surround mode buttons

Numeric buttons

Used to enter figures in the selection of a tuner pre- set station and station name preset or to select a CD track number, etc. The functions of these buttons are dependent on the function button selected.

Surround mode buttons (when AMP mode is selected)

Used to select the surround mode.

.CL (clear) / S-DIRECT (source direct)

button

Used to cancel certain memory or programming operations.

(when AMP mode is selected)

Used to select the S-DIRECT (source direct) mode.

In source direct mode, the tone control circuitry is bypassed.

⁄0INPUT button

Used to select monitor input.

Note:

This button is unavailable for SR6400.

⁄1T.MODE button

(when TUNER mode is selected)

Used to select the auto stereo mode or mono mode when the FM band is selected.

The “AUTO” indicator is illuminated in the auto stereo mode.

⁄2(TV) CH 3/4 buttons

Used to increase or decrease the TV channels.

⁄3TOP MENU button

(when DVD mode is selected)

Used to call up the top menu of the DVD.

⁄4Tone / Deck control buttons

Tone control buttons (when AMP mode is selected)

The TREBLE buttons are used to adjust the tone control of high frequency sounds for the left and right speakers.

The BASS buttons are used to adjust the tone con- trol of low frequency sounds for the left, right and subwoofer speakers.

Deck control buttons (when Tape mode is selected)

The DECK A button is used to select deck A. The DECK B button is used to select deck B.

The 1 2 buttons are used to change the direction.

⁄5CURSOR / OK button

Used to operate on-screen and other displays used by receivers and other components.

⁄6CH SEL. (channel select) button

(when AMP mode is selected)

Used to call up SETUP MAIN MENU and adjust speaker levels or 6.1 ch input level.

⁄7SETUP button

(when AMP mode is selected)

Used to call up the SETUP MAIN MENU of the SR6400.

⁄8CONTROL buttons

These buttons are used when operating the CD player, TAPE deck, etc.

The function of these buttons are dependent on the function button selected.

(when AMP mode is selected)

ATT button

When the input signal is too high and the voice dis- torts even while adjusting the SR6400 VOLUME control, turn on this function. “ATT” is illuminated when this function is activated.

The input level is reduced. Attenuator is invalid for the output signal of “REC OUT”.

Note:

This function is unavailable while the digital input is selected.

SPKR A/B button

Speaker mode is switched in the following sequence. A B A+B off

Note:

The MULTI button is unavailable for SR6400.

⁄9Input selector buttons/ FUNCTION

SELECTOR buttons (AUDIO/VIDEO INPUT)

Used to switch the remote control to the command sets for specific sources (amplifier, receiver, etc.), thereby allowing a single remote control to control up to 11 different components. To use these buttons to switch the amplifier’s source, press the desired button twice within 2 seconds. The AMP button is used only to switch command set of the remote control itself and therefore does not transmit any signal. Further, the function buttons may also be programmed to execute macros. (A macro allows a complex string of operations to be performed in series simply by pressing a single button.) One button can be programmed to learn sequences containing up to 10 commands. The following is an example of such a sequence that can be activated automatically using a macro:

Turn the receiver ON Switch the function to DVD Set the Surround Mode to VIRTUAL Set the DVD player to Play.

Note:

The AUX2 button is unavailable for SR6400.

¤0EXIT button

(when AMP mode is selected)

Used to exit setup menu.

ENGLISH

7

Page 10
Image 10
Marantz SR6400 manual Names and Functions