Marantz SR6400 manual → B → C ... Z → 1 → 2 → 3 .... → → + → / → Blank → a UP →, ← Down

ENGLISH	(Using the remote control unit)
	1.	Tune into the radio station you desire (Refer to
		the “MANUAL TUNING” or “AUTO TUNING”
	2.	section).
		Press the MEMO button on the remote. “– –“
	3.	(preset number) starts blinking on the display.
		Enter the desired preset number by pressing
		the numeric buttons.

Note:

•When entering a single digit number (2 for example), either input “02” or just input “2” and wait for a few seconds.

RECALLING A PRESET STATION

2.1.

SELECTOR

DOWN UP

	CLEAR		TUNING	F/P		MODE
TV	DVD	VCR1		TAPE	CD	TUNER

AUX INPUT

1. 1.

(Using the SR6400)

1. Press the F/P button to show the preset station on the display.

2. Select the desired preset station by pressing the TUNINGorbuttons on the front panel.

(Using the remote control unit)

1. Press the 4 or ¢ buttons to select the desired preset station, or input your desired preset channel with the numeric buttons on the remote.

26

PRESET SCAN

3.

1. 3.

(Using the remote control unit)

1. Press the P.SCAN on the remote.

“PRESET SCAN” appears on the display and then the preset station with the lowest preset number is recalled first.

2. Preset stations are recalled in sequence (No.1

→No.2 → etc.) for 5 seconds each.

No stored preset number will be skipped.

3. You can fast forward the preset stations by pressing the ¢ continuously.

When the desired preset station is received, cancel the preset scan operation by pressing the CL button or P.SCAN on the remote.

CLEARING STORED PRESET STATIONS

You can remove preset stations from the memory using the following procedure.

2.3.

V SURROUND RECEIVER SR6400

3.

	CLEAR	MEMORY	TUNING
ENTER			2.
	TVDVD	VCR1	DSS/VCR2 AUXCD-R
PHONES
1.	Recall the preset number to be cleared with the
2.	method described in “Recalling” a preset station.
	Press the MEMORY button on the front panel or
3.	press the MEMO button on the remote.
	The stored preset num blinks in the display

for 5 seconds. While blinking, press the CLEAR button on the front panel or press the CL button on the remote.

4. “xx CLEAR” appears on the display to indicate that the specified preset number has been cleared.

Notes:

•To clear all stored preset stations, press and hold the CLEAR and the F/P buttons for two seconds.

SORTING PRESET STATIONS

SELECTOR

DOWN UP

	CLEAR		TUNING	F/P		MODE
TV	DVD	VCR1		TAPE	CD	TUNER

AUX INPUT

If you have stations memorized, and there is a gap in the sequential order:

I.e. the stations are stored as follows

1)87.1 MHz

2)93.1 MHz

3)94.7 MHz

10)105.9 MHz

(notice there is no stations programmed for pre sets for 4-9), you can have pre set 10 become pre set 5:

To sort the numbers, press and hold the MEMORY and the F/P buttons.

“PRESET SORT” will appear on the display and sorting will be done.

NAME INPUT OF THE PRESET STATION.

This function allows the name of each preset channel to be entered using alphanumeric characters. Before name inputting, you need to store preset stations with the preset memory operation.

4.	5. 6.	4.	2. 5. 6.		5.
	SELECTOR
		CLEAR	TUNINGF/P	MODE	DOWN	UP
	TV	DVDVCR1	TAPE	CD	TUNER
						AUX INPUT

4.	5.
2.	4.
5.
6.

1. Recall the preset number to be inputted name with the method described in “Recalling” a preset station.

2. Press the MEMORY button on the front panel or press the MEMO button on the remote for more than 3 seconds.

3. The left most column of the station name indicator flashes, indicating the character

entry ready status.

4. When the SELECT knob is turned or you press the 5 / 6 buttons on the remote, alphabetic and numeric characters will be displayed in the following order:

A → B → C ... Z → 1 → 2 → 3 ..... 0 → – → +

→/ → (Blank) → A UP →

←DOWN

5.After selecting the first character to be entered, press the MEMORY or ENTER buttons, press the MEMO button on the remote.

The entry in this column is fixed and the next column starts to flash. Fill the next column the same way.

To move back and forth between the characters, press the TUNING/buttons or press the 4 or ¢ buttons on the remote.

Note:

•Unused columns should be filled by entering blanks.

6.To save the name, press the MEMORY or the ENTER button, press the MEMO button on the remote for more than 2 seconds.

Ten keypad Press, press again, press again, etc.

1A → B → C → 1 → A

2D → E → F → 2 → D

3G → H → I → 3 → G

4J → K → L → 4 → J

5M → N → O → 5 → M

6P → Q → R → 6 → P

7S → T → U → 7 → S

8V → W → X → 8 → V

9Y → Z → space → 9 → Y

0– → + → / → 0