Maytag Clothes Dryer manual Low

Normal, or I_ess Dry. Selecting More Dry, Normal, or I.ess Dry automatically adjusts the dryness [eve[ at which the dryer will shut off.

more dry

normal

less dry

sensor cycles ] dryness

•Press the WRINKI.E PREVENT feature button if this option is desired.

•Press the SIGNAl. ON/OFF button to set the end of cycle signal

•Press and hold START/PAUSE button until dryer starts (about 1 second).

The Wrinkle Prevent and Cycle Signal features can be adjusted during a Sensor Cycle. If you want to select another Sensor Cycle or Sensor Cycle Dryness, press START/PAUSE once to stop the dryer, make the desired changes, then press START/PAUSE to resume drying.

NOTES:

A default time is displayed when a Sensor Cycle is selected. During the first few

minutes of the drying process, the cycle time may automatically vary from the default time based on the size and fabric type of the load. Toward the end of the drying process, the estimated time display will adjust again, showing the final drying time.

•Time and Temperature are not adjustable for Sensor Cycles. Pressing the TIME ADJUST or TIMED CYCI_ES TEMP buttons will cause a triple beep, indicating that the time cannot be changed.

•A light next to each feature will glow yellow when the feature is selected. The light

will not glow when the selection is unavailable with the cycle or option combinations selected.

•Sensor Cycles Dryness can be changed only with Sensor Cycles. This feature is not se[ectab[e for Timed, Steam, or Sanitize cycles.

How Sensor Cycles Work

The Sensi-Care TMdrying system improves performance with Auto Moisture Sensing Plus, which advances the cycle as moisture is extracted from clothing. A thermistor (electronic temperature sensor) and moisture sensing strips in the dryer drum help measure the amount of moisture in the clothes as they tumble. An electronic control determines the load type to help save time, avoid overdrying, and increase the accuracy of the end dryness [eve[. After the first 5 minutes of a Sensor cycle, the estimated time display will adjust based on the approximate load size, cycle, dryness [eve[ selected and amount of

moisture left in the clothes. When the clothes have reached approximately 80% of the dryness [eve[ selected, the estimated time display will adjust again, showing the final drying time. Sensi-Care TMtakes the guesswork out of drying time and enhances fabric care.

To use a Timed Cycle

•Press POWER/CANCEl .....

•Rotate the dial to select a Timed Cycle.

•Press the TIME ADJUST up or down buttons until the desired drying time is displayed. Press TIME ADJUST, and the time will change by 1-minute intervals. Press and hold TIME ADJUST, and the time will change by 5-minute intervals. The initial time displayed is the actual drying time.

time adjust

Q

The Time Adjust feature can be used only with Timed Cycles.

•Press TIMED CYCI.ES TEMP until the desired temperature glows yellow. high

eregular medium

S low

air dry

l timed cycles i temp

Temperature settings can be changed only with Timed Cycles.

•Press the WRINKI.E PREVENT feature button if this option is desired.

•Press the SIGNAl. ON/OFF button to set the end of cycle signal

•Press and hold START/PAUSE button until dryer starts (about 1 second).

NOTES:

•Sensor Cycles Dryness is not adjustable for Timed, Steam, or Sanitize Cycles. Pressing the SENSOR CYCI_E DRYNESS button will cause the triple beep indicating that this option is not se[ectab[e.

•A light next to each feature will glow yellow when the feature is selected. The light will not glow when the selection is unavailable with the cycle or option combinations selected.

•While a Timed Cycle is running, you can change the settings for Time, Temperature, the WRINKI.E PREVENT feature and the cycle signals. Press the START/PAUSE button once to stop the dryer, allowing you to select another cycle.