29
ENGLISH
9.5 Machine Cleaning
Remove chips and saw dust with brush
or vacuum from:
−setting devices;
−the operating elements;
−motor vent slots;
−space below table insert.
9.6 Machine storage
ADanger!
•Store the saw in such way that it
cannot be used or tampered with
by unauthorised persons.
•Make sure that nobody can get
injured by the stored machine.
ACaution!
•Do not store saw unprotected
outdoors or in damp environ-
ment.
•Observe the permissible ambient
conditions (see "Technical Speci-
fications").
9.7 Maintenance
Prior to every use
•Remove saw dust and chips with
vacuum or brush.
•Check power cable and power cable
plug for damage; if necessary, have
damaged parts replaced by a quali-
fied electrician.
•Check all moving parts to see that
they can move freely across their
whole range of travel.
Periodically, depending on operating
conditions
•Check all screwed joints, retighten if
necessary.
•Check pull-back springs of the saw-
head (the sawhead must return by
spring power to its upper starting
position), replace if necessary.
−For long stock use suitable supports
on both sides of the saw.
−When performing bevel cuts, hold
the workpiece on the right side of
the saw blade.
−Use auxiliary fence when sawing
small cut-offs (this may be a suitable
board, fastened with four screws to
the fence).
−When cutting warped stock, place
the convex side of the bow against
the fence.
−Do not cut stock standing on edge;
always place it flat on the rotating
table.
−Keep the supporting surfaces clean
– in particular, remove resin residue
with a suitable cleaning and mainte-
nance spray.
For special tasks the following accesso-
ries are available at your specialised
dealer – see back cover for illustrations:
AMulti-Suction Adapter
To connect different dust collection
attachments.
BTable Extension
Required when cutting long stock;
folds up to save space.
CWork Stand
For a secure machine stand and
optimal working height;
folding, ideal for mobile use.
DTCT saw blade 210 x2.0 / 1.4 x30
20 alternate bevel teeth
for wood and non-laminated parti-
cle board.
ETCT saw blade 210 x 2.4 / 1.8 x 30
40 alternate bevel teeth
For wood and panels.
ADanger!
Repairs to electric tools must
be carried out by qualified electri-
cians only!
Electric tools in need of repair can be
sent to the Service Centre of your coun-
try. Refer to the spare parts list for the
address.
Please attach a description of the fault to
the electric tool.
The machine's packing can be 100%
recycled.
Worn out power tools and accessories
contain considerable amounts of valua-
ble raw and rubber materials, which can
be recycled.
These instructions are printed on paper
produced with elemental chlorine free
bleaching process.
This section describes problems and
malfunctions which you should be able
to resolve yourself. If the measures
described here do not solve your prob-
lem, see under "Repairs".
ADanger!
Many accidents happen partic-
ularly in connection with problems
and faults. Therefore please note:
•Always unplug before servicing.
•Check to see that all safety
devices are operational after each
fault service.
Motor does not run
No mains voltage
•Check cables, plug, outlet and
mains fuse.
No crosscut function
Transport locking pin engaged:
•Pull transport locking pin out.
Safety lock engaged:
•Actuate the safety lock.
Only little sawing performance
Saw blade blunt (possibly tempering
marks on blade body):
Saw blade not suitable for material being
cut (see chapter "Technical Specifica-
tions");
Saw blade warped:
•Replace saw blade (see chapter
"Maintenance").
Saw vibrates heavily
Saw blade warped:
•Replace saw blade (see chapter
"Maintenance").
Saw blade incorrectly mounted:
•Mount saw blade correctly (see
chapter "Maintenance").
Stiffness of rotating table
Saw dust build-up under rotating table:
•Remove saw dust.
10. Tips and Tricks
9493
11. Available Accessories 12. Repairs 13. Environmental Protection 14. Troubleshooting Guide