MHP JNR, WNK General Instructions, Safety, Assembly Instructions, Storage, Operating Safeguards

Models: WNK

1 32
Download 32 pages 39.58 Kb
Page 5
Image 5
GENERAL INSTRUCTIONS

GENERAL INSTRUCTIONS

This installation guide provides you with easy to fol- low illustrations and instructions to assemble your MHP Gas Barbecue Grill.

Before you start assembling and using your MHP Gas Barbecue Grill we recommend that you read through all precautions, safe guards and instruc- tions to avoid any personal injury or property damage.

Check Local Codes. Contact your local LP dealer or Natural Gas company for recommended installation procedures and regulations. If there are no local codes, installation must conform to the latest National Fuel Gas Code: ANSI Z 223.1. For Canada, installa- tion must comply with local codes and/or Standard CAN/CGA-B-149-1 for natural gas installation and CAN/CGA- B-149-2 for propane installation.

For LP Gas Models the supplied Gaslow GS-801 Regulator must be used. Any replacement pressure regulator or hose assembly must meet or exceed the specifications of the Gaslow GS-801 Regulator.

For Natural Gas Models the grill is designed to oper- ate at a pressure of 7” water column (W.C.) (1.75 kPa). Check your gas utility for local pressure. Pres- sures other than approximately 7” W.C. could affect the performance of your grill.

ASSEMBLY INSTRUCTIONS

There are 9 steps to assembling your MHP Gas Bar- becue Grill: The mounting, LP tank mounting, control panel, gas supply connection, grill lid, lid handle, side shelves, and rock grate, cooking grid and warming rack.

The grill itself is partially assembled with the Burner, Venturis, Ignitor Collector Box and the Gaslow Regu- lator installed.

The JNR and WNK grills are specifically designed to fit the five mounting methods: Cart, In-Ground Post, Deck/Patio Base, Optimum Console and Built-in. The TJK Grill is supported by the Optimum Console mounting and Built-in.

You will need the following tools to assemble your grill:
A Phillips head screwdriver

A standard flat head screwdriver

Two 7/16” wrenches or sockets

General Instructions

STORAGE

Turn gas OFF at the LP cylinder (or at the shut OFF valve in the case of Natural Gas) when the MHP Gas Barbecue Grill is not in use.

Do not store spare LP cylinders under the MHP Gas Barbecue Grill.

Store disconnected LP cylinders outdoors in a well- ventilated area, do not store in shed, building, garage or in any enclosed area.

OPERATING SAFEGUARDS

Do not install your MHP Gas Barbecue Grill in or on recreational vehicles and/or boats.

Never use your MHP Gas Barbecue Grill near combustible surfaces, including roof over- hangs, roofs, vinyl siding and window shut- ters. Maintain at least a 6-foot clearance.

Use this barbecue outdoors in a well- ventilated area.

Do not use your MHP Gas Barbecue Grill in a shed, garage, building, breezeway or any other confined area.

Do not use any kind of combustible material on or near the top, bottom, back or sides of the grill. Maintain at least a 2-foot clearance.

Leak test all gas supply line connections.
Do not let children operate a gas grill.

Keep the area around the grill clear of com- bustible vapors or liquids such as gasoline.

When operating the grill do not leave unat- tended. Keep children and pets away.

Keep fuel supply hose and electrical supply cord away from any heated surface.

ASSEMBLY INSTRUCTIONS SAFETY

YOUR GRILL IS DESIGNED FOR OUTDOOR USE ONLY.

It should also not be used in an enclosed area such as a shed or garage because combustion uses available oxygen and dis- charges carbon monoxide.

The grill must be located no closer than 24" from any combus- tible surface behind or to the sides. Grill should not be located under overhead unprotected combustible surfaces.

Keep the area around the grill clear of combustible materials, flammable vapors or liquids such as gasoline.

Do not obstruct the flow of combustion and ventilation air.

5

Page 5
Image 5
MHP JNR General Instructions, Safety, Assembly Instructions, Storage, Operating Safeguards, Two 7/16” wrenches or sockets