Manuals / Miele / Kitchen Appliance / Dishwasher

Miele G 7883 CD Frequently asked questions, What if, Possible fault, Solution, show signs of

Models: G 7883 CD

1 76

Download 76 pages 2.29 Kb

Page 60

Frequently asked questions

What if...	Possible fault		Solution
Items made of glass	The items are not		Only use washer-safe
show signs of	washer-safe.		glassware.
corrosion.	No neutralization took		Fill the neutralizer
	No neutralization took		Fill the neutralizer
	place in the program		container.
	sequence.
	Excessively high		Select an appropriate
	temperatures are causing		program or lower the wash
	glass corrosion.		temperature.
	Too alkaline detergent is		Choose a milder detergent
	causing glass corrosion.		or lower the DOS1
			concentration.
Items made of stainless	The chloride content of the		Test your water
steel show signs of	water is too high.		composition. If needed,
corrosion.			condition the water
			externally and use DI
			water.
	The screw cap on the		Properly thread the cap
	reactivation salt reservoir is		and screw it tightly.
	not tightened.
	No neutralization took		Fill the neutralizer
	place in the program		container.
	sequence.
	Rust articles or a rust film		– Check the piping.
	appears in the wash		– Remove all rusty items
	cabinet, due to:		from use.
	–	excessive iron content in
		the water, or
	–	rusty items in the
		washer.
	The grade of stainless		Only use high grade
	steel is not washer-safe.		stainless steel.

60

Image 60

Miele G 7883 CD Frequently asked questions, What if, Possible fault, Solution, Items made of glass, show signs of

Contents

Operating and Installation Instructions Laboratory Glassware Washer G 7883 CDen - US, CA Page Contents Contents Program Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Programming functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 The following instructions apply to all programming functions:. . . . . . . . . . . . . . . 36 To access the programming mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Saving to memory and exiting the programming mode . . . . . . . . . . . . . . . . . . 36 Exiting the programming mode without saving . . . . . . . . . . . . . . . . . . . . . . . . 36 DOS 1 liquid detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Setting the detergent dosage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Priming the dosage system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 DOS 3 neutralizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Setting the neutralizer dosage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Priming the dosage system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Changing program parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Changing the temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Changing the holding time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Restoring the factory settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Setting the time and date. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Resetting the coarse and fine filter timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Data transfer optional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Routine checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Frequently asked questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Thermo switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 After Sales Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 INSTALLATION INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Plumbing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS ~Take care when handling processing chemicals detergents, softeners, neutralizers, etc.. These may contain irritant or corrosive ingredients. Do not use organic solvents as these could cause an explosion. Wear protective gloves and goggles. With all chemical agents the manufacturer’s safety conditions must be observedIMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Please note the following symbols on the machineAccessories SAVE THESE INSTRUCTIONSGuide to the lab washer h Service panel i Serial interface Guide to the lab washera Drying unit c Dispenser for powdered detergentDescription of the machine Standard modelIntended applications: Laboratory equipment Opening and closing the door Electric door lockTo open the door To close the doorSetting the water softener Water softenerSettings factory settingWater softener Filling the salt reservoir Water softenerSalt indicator Water softenerRinse Aid Adding rinse aidRinse aid indicator light Setting the rinse aid dosageRinse Aid Neutralizing agent Adding neutralizerNeutralizer indicator light Neutralizing agentSetting the liquid detergent dosage DetergentAdding detergent Liquid detergent refill light DetergentDetergent ^Load the detergent into the compartment^Snap the cover closed Loading the machine Loading the machine Loading the machinePrepare items before loading Special preparations before operating the machineAdjusting the upper basket Spring adapter for the water connectionTo adjust the upper basket Loading the machineLaboratory equipment Loading the machineLoading the machine Upper basket OFor various inserts Lower basket ULoading the machine E Injector wagonO Injector wagon For narrow necked glasswareTurning on Starting a programSelecting the optional drying function Program sequence display End of a program Turning offAdditional drying Canceling a program Program Guide Program Guide Program sequenceProgramming functions To access the programming modeSaving to memory and exiting the programming mode Exiting the programming mode without savingDOS 1 liquid detergent Setting the detergent dosageProgramming functions StepDOS 3 neutralizer Setting the neutralizer dosageProgramming functions StepBuzzer Programming functionsChanging program parameters Programming functionsChanging the wash and rinse parameters Changing the drying parametersChanging the temperature Step Programming functionsChanging the holding time Step Display / ResultRestoring the factory settings Programming functionsSetting the time and date Programming functionsResetting the coarse and fine filter timer Programming functionsData transfer optional Maintenance Routine checksCleaning and Care Cleaning the filters in the wash cabinetCleaning and Care Cleaning the fine, flat and micro-finefiltersCleaning the spray arms Cleaning and CareRemoving the spray arms Cleaning the drain pump and non-returnvalve Cleaning and CareCleaning the water inlet filters Cleaning and CareCleaning the filters Cleaning the control panel Cleaning the exteriorCleaning the wash cabinet Cleaning the door sealBaskets and inserts Cleaning and CareFrequently asked questions Possible faultSolution What ifFrequently asked questions What ifFrequently asked questions What ifFrequently asked questions What ifFrequently asked questions What ifFrequently asked questions What ifFrequently asked questions Possible faultSolution What ifFrequently asked questions Possible faultSolution What ifFrequently asked questions Possible faultSolution What ifThermo switch Frequently asked questionsAfter Sales Service V1-800-565-6435service@miele.caU1-800-991-9380techserv@mieleusa.com INSTALLATION INSTRUCTIONS Installation Leveling the legsPositioning and securing the machine Removing the lid if necessary Protecting the countertopInstallation Cover plate protects the countertopElectrical connection THIS APPLIANCE MUST BE GROUNDEDGrounding connection Connecting the water inlet PlumbingPlease also refer to the installation diagram PlumbingPlumbing DI Connection pressurizedDI connection unpressurized optional Drainage PlumbingTechnical data EnglishMetric Caring for the environment Disposal of the packing materialsDisposal of an old appliance Page Subject to change without notice / M.-Nr.07 157 440 /