Stop engine and let cool | Miller Electric OM-129, 500DX R specs

7-9. Inspecting And Cleaning Optional Spark Arrestor Muffler

Tools Needed: 3/8 in

YStop engine and let cool.

1 Spark Arrestor Muffler

2 Cleanout Plug

Remove plug and remove any dirt covering cleanout hole.

3 Exhaust Pipe

Start engine and run at idle speed to blow out cleanout hole. If nothing blows out of hole, briefly cover end of exhaust pipe with fireproof material.

YStop engine and let cool. Reinstall cleanout plug.

ST-800 633-B / Ref. ST-180 933-B

7-10. Overload Protection For Models With CV Option

1 Circuit Breaker CB3

CB3 protects the 115 volt ac output to Remote receptacle RC3 and ter- minal strip 2T.

If CB3 opens, the 115 volt ac output stops.

2 Circuit Breaker CB4

CB4 protects the 24 volts ac output to Remote receptacle RC3 and ter- minal strip 2T.

If CB3 opens, the 24 volt ac output stops.

. Press button to reset circuit

	breaker. If a breaker continues
	to open, contact Factory Au-
1	thorized Service Agent.
1
2

ST-800 862-A / ST-148 404

OM-129 647 Page 34

Page 38

Image 38

Miller Electric OM-129, 500DX R manual Inspecting And Cleaning Optional Spark Arrestor Muffler, Stop engine and let cool

Contents

Description OM-129 647WProcesses From Miller to You Table of Contents Page Electric Shock can kill Symbol UsageArc Welding Hazards ARC Rays can burn eyes and skin Engine Hazards Engine Exhaust Gases can kill Battery Explosion can BlindMoving Parts can cause injury Engine Heat can cause fire Radiation can cause interference Principal Safety StandardsEMF Information ARC Welding can cause interference UN Choc Électrique peut tuer Signification des symboles− Consignes DE Sécurité − Lire Avant Utilisation LES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures graves LE Soudage peut provoquer un in- cendie ou une explosionDES Particules Volantes peuvent blesser les yeux LE Bruit peut affecter l’ouïe LA Chaleur DU Moteur peut pro- voquer un incendie DES Organes Mobiles peuvent provoquer des blessures’EXPLOSION DE LA Batterie peut LA Chute DE L’APPAREIL peut blesser LE Soudage À L’ARC risque de provoquer des interférences Principales normes de sécuritéInformation sur les champs électromagnétiques Consignes relatives aux stimulateurs cardiaques Weld, Power, And Engine Specifications − SpecificationsSymbols And Definitions − Definitions Fuel Consumption Dimensions, Weights, And Operating AnglesCurve shows typical fuel use under weld or power loads 1898 lb 861 kg Engine End Duty Cycle And Overheating AC Auxiliary PowerWarranty Minutes Welding Minutes Resting 60% Duty Cycle At 500 Amperes Duty Cycle is Percentage Volt-Ampere Curves CC/DC Standard CV/DC Models With CV Option Optional AC Power Plant Curves Do Not Lift Unit From End Airflow Clearance − InstallationInstalling Welding Generator Location Charger Activating The Dry Charge BatteryWhen electrolyte is low, add Maintain proper level Connect Negative − Cable Last Connecting The BatteryEngine Prestart Checks Tools Needed 1/2 Connecting To Weld Output Terminals Selecting Weld Cable Sizes Remote A/V Control Receptacle RC3 Installing Ether Cylinder Optional Ether Starting AidAfter installing cylinder, wait at Socket Remote 14 Receptacle RC3 Information OptionalTerminal Strip 2T Connections Optional Stop engine − Operating the Welding Generator Standard Controls See Section If light goes off, stop engine and check oil level Do not switch under loadDescription Of Standard Controls See Section If light goes on, stop engine and check engine belt Controls For Models With CV Option See Section This unit has a max OCV control circuit Volt And 240 Volt Duplex Receptacles Auxiliary power is not affected by weld output− Operating Auxiliary Equipment 120 V 15 a AC Receptacle RC2 240 V 15 a AC Receptacle RC1 Australian And South African Receptacle Options Optional Auxiliary Power ReceptaclesGfci Receptacle Option British Receptacle Option 1011 Connecting Optional Auxiliary Power PlantSet Engine Control switch to Run when using auxiliary power Load Terminals − Maintenance & Troubleshooting Maintenance Label Deutz F3L912 Diesel Engine Hose Servicing Air CleanerTo clean air filter Servicing Fuel And Lubrication Systems 1850 Adjusting Engine SpeedServicing Optional Ether Starting Aid 13 mm Max Tools Needed 11/16 To adjust belt tensionChecking And Replacing Alternator Belt Stop engine To check belt tension Resetting Fan Belt Safety Shutdown Overload Protection For Models With CV Option Inspecting And Cleaning Optional Spark Arrestor MufflerStop engine and let cool. Reinstall cleanout plug Stop engine and let cool Troubleshooting Welding Auxiliary Power Engine Trouble Remedy OM-129 647 − Electrical Diagrams Circuit Diagram For Welding Generator Standard Models Circuit Diagram For Welding Generator Models With CV Option 184 954-C − RUN-IN Procedure Wetstacking Run-In Procedure Using Load Bank Load Bank Bank/grid Run-In Procedure Using Resistance GridDo not touch hot exhaust From flammables Grounding Generator To Truck Or Trailer Frame − Auxiliary Power GuidelinesSelecting Equipment Earth ground if supplying Grounding When Supplying Building SystemsHow Much Power Does Equipment Require? Use ground device as stated in electrical codes Industrial Motors Rating Starting Watts Running Watts Approximate Power Requirements For Industrial MotorsApproximate Power Requirements For Farm/Home Equipment Farm/Home Equipment Rating Starting Watts Running Watts Approximate Power Requirements For Contractor Equipment Contractor Rating Starting Watts Running Watts Single-Phase Induction Motor Starting Requirements Power Required To Start MotorHow Much Power Can Generator Supply? KVA/HP x HP x 1000 = Starting Amperage Volts Welding Generator Auxiliary Power output circuit Generator is to supply standby power duringEmergencies or power outages Customer-supplied equipment is required if Selecting Extension Cord Use Shortest Cord Possible − Parts List 101 100 66 65 102 Dia Part Description Quantity Mkgs Optional Panel, Front w/Components CC Model Illustrated Panel, Front w/Components -1 Item Generator 6 5 Generator -1 Item Includes 171Hardware is common Not available unless listed Control Box CC/CV -1 Item 86 Optional Panel, Mtg Components CC/CV Model Panel, Mtg Components CC Model Page Support ServiceYour distributor also gives For assistance in filing or settling claims Miller Electric Mfg. CoTo locate distributor nearest you call 1-800-4-A-Miller