Mitsubishi Electronics DX-TL4516U instruction manual 109, LOG54

Warning Display		Countermeasure	Cancelling	Log number		CALL OUT	Page
						output
			the warning
						#1
No Camera Signal		• Check whether the unit and	Stop	LOG54	#7	Fixed	18
		camera are properly connected	recording.
Camera signal is lost or distorted.		and turned on.
Please check the camera and cable		• Check whether the video signal is Output video					–
connection.		being properly outputted.	signals.
		• Check whether the camera with	Click "Clear				49-51,
		no video signal input is set for	Warning" or press				91
		operation.	the E button.
It can use as it is though a slight error		• Continue the operation when	Automatically	LOG13	#8	None	–
occurred.		there is no abnormality.	clears after 1	LOG33	#8
		• When the error occurs	minute.	LOG43	#8
		continuously, check the		LOG73	#8
		HDD/media and cable and then		LOG23	#8
		restart the unit.
System suspended due to unstable		• Restart the unit.	Click "Clear	LOG14	#8	Fixed	–
processing. Recording will be resumed.			Warning" or press
HDD	was disconnected.		the E button.
System suspended due to unstable				LOG74	#8
processing. Start operation again.			Automatically	LOG24	#8	None
			clears after 1	LOG34	#8
			minute.	LOG44	#8
The recorder detected the data altered or data			Click "Clear	LOG55	#7	None	78
recorded by other recorder.			Warning" or press
			the E button.
Recorder detected technical problems			Click "Clear	LOG6200		Fixed	–
on the device.			Warning" or press
			the E button.
The recorder has been rebooted. The problem • Check the unit.			Click "Clear	LOG5100		Fixed	–
is not critical, but check the recorder.			Warning" or press
			the E button.
Internal temperature is getting too high,		• Turn off the power and change	Click "Clear	LOG5200		Fixed	–
check the ventilation of the recorder.		the installation condition.	Warning" or press
			the E button.
Internal temperature is getting too high,		• Turn off the power and change	Click "Clear	LOG5201		Fixed	–
stop the operation of the recorder		the installation condition.	Warning" or press
immediately.			the E button.
			Lower the
			temperature.
The fan of the recorder needs to be checked.		• Turn off the power and stop	Click "Clear	LOG5300		Fixed	–
		using.	Warning" or press
			the E button.
			Rotate the fan.
Copying data stopped because of new record		• Stop HDD recording to continue	Click "Clear	LOG3500#5		None	41, 42
overwrites the old data.		copy/backup.	Warning" or press	LOG7500#6
			the E button.
New record will soon overwrite the old data		• Stop HDD recording to continue	Click "Clear	LOG3600#5		None	41, 42
in copying.		copy/backup.	Warning" or press	LOG7600#6
Stop the recording, if you want to continue the • Stop copy/backup to continue			the E button.
copying.		HDD recording.
(NONE)		• Restarts by watchdog operation		LOG5101		–	–
		or for self-recovery.		LOG5102
				LOG5103

#Regarding LOG14 : Displays during recording. The system shuts down once and then resumes recording. (The error HDD is automatically deleted from the recording device. The recording is continued until all the registered HDDs are used up.)

#Regarding LOG24 to 74: Displays during copying or playback. The playback or copy stops because the system shuts down. Carry out playback or copy again.

#Regarding LOG 54: Displays during recording when the video signal is not existed for the camera being recorded for 2 seconds or more. This warning may not be displayed for the recording of which recording time is less than 2 seconds.

Warnings and CALL OUT output

109