Manuals / Motorola / Home Audio / Stereo Amplifier

Motorola BT100 Torque Specifications, Fastener, Screw Size, Wrench Size, In-lbs, Appendix B

Models: BT100

1 52

Download 52 pages 62.92 Kb

Page 50

Appendix B

Torque Specifications

Torque specifications are valid for the BT100.

				Torque
Fastener	Screw Size	Wrench Size	In-lbs	Ft-lbs	N•M
Strand clamp/pedestal	5/16-18	1/2 inch	120-144	10-12	13.6-16.3
mounting
Housing/lid closure	5/16-18	1/2 inch	180	15.0	20.4
Test point plugs	5/8-24	1/2 inch	25-40	2.1-3.3	2.8-4.5
Seizure screw	#8-32	3/16 inch or	12	1.0	1.4
		Phillips
Hybrid	#6-32	Phillips	10-12	0.8-1.0	1.1-1.4
Chassis (electronics	#10-32	5/16 inch	18-22	1.5-1.8	2.0-2.4
module)
Chassis (electronics	#6-32	1/4 inch or	10-12	0.8-1.0	1.1-1.4
module) cover		Phillips
Status monitor	#10-32	5/16 inch	24-30	2.0-2.5	2.7-3.4
Power supply cover	#6-32	1/4 inch or	10-12	0.8-1.0	1.1-1.4
		Phillips

BT100 Installation and Operation Manual

Image 50

Motorola BT100 operation manual Torque Specifications, Fastener, Screw Size, Wrench Size, In-lbs, Appendix B

Contents

BT100 1 GHz Broadband Telecommunications AmplifierCaring for the Environment by Recycling Recycling your Motorola EquipmentCanadian Compliance Safety StandardsFCC Compliance International Declaration of ConformityIntroduction ContentsAmplifier Setup OverviewSpecifications Bench TestingInstallation Torque Specifications Abbreviations and AcronymsFigures TablesIntroduction Section1-2Introduction Figure 1-2illustrates an open BT100Figure BT100 - open Document Conventions Using This ManualRelated Documentation Technical Response Center If You Need HelpIssued 04/2005 Inside the U.S. 888-944-HELP Outside the U.SCalling for Repairs Figure BT100 - open OverviewSection Figure BT100 output-portconfigurations 2-2OverviewOrdering Guide Figure BT100 ordering guideFigure BT*-100*/15dimensions - side view HousingFigure BT*-100*/15dimensions - top view Overview2-5 Housing Gaskets Housing port locations and rear view of housing Power SupplyPort Locations BT100 power supply 2-8OverviewForward Path Figure Fuse locationsFigure BT100*-4*four output block diagram 2-10OverviewReturn Path BT100*-3*three output block diagramIngress Control Switch Figure LL-BTA-HMSstatus monitorDescription Options and AccessoriesModel FunctionDescription Figure BT100 Options and AccessoriesModel FunctionBench Setup Amplifier SetupProper Handling Procedures Field PracticeForward Path Alignment Before You BeginSTARLINE Forward Equalizers 1003 Frequency MHz versus Insertion Loss dBEqualizer ValueCable slope in dB STARLINE Cable SimulatorsFrequency Input, Midstage, and Output Pads Figure Frequency versus cable slopeFlatness Control Figure Flatness controlsDirectional Coupler Test Points Bode EqualizationManual Gain Control TemperatureAmplifier Level Control Gain ReserveThermal Drive Unit Automatic Drive Unit/QAM Automatic Drive Unit Before You Begin Return Path AlignmentADU/QADU Pads and Levels Alignment Procedure Powering and Surge Protection Test Equipment and Connections Bench TestingBefore You Begin SectionMeasuring Forward Gain Testing Return Gain and Response Completing the Test Procedures Section InstallationAerial Installation Jumper position Description Pedestal Installation Grounding the BT100Operating Tips Using Amplifiers in Lower Frequency SystemsUsing Amplifiers in Lower Gain Systems SectionModel BT100 SpecificationsSpecification Forward AmplifierADU/QADU Automatic Drive Unit AC CurrentRA-Kit/HReturn Amplifier AC VoltageFastener Torque SpecificationsTorque Screw SizeAbbreviations and Acronyms 2/07 Visit our website at527550-001-a